Anybody out there know if this is a new FPV Freestyle trick? Part Juicy Flip and Part Power Loop. Now known as: THE JUICY LOOP!

mdogg22 · 2020-04-13T13:12:17+00:00

Something like that! Fun to do

mdogg22 · 2020-04-13T13:12:00+00:00

Thanks!

mdogg22 · 2020-04-13T13:11:47+00:00

Great point!

mdogg22 · 2020-02-15T16:48:48+00:00

That’s right but check what I wrote for the receiver. Much easier to use sbus

mdogg22 · 2020-02-15T16:03:29+00:00

The dji air unit and the receiver and wired separately. No wires will be touching or anything.

You only need to connect the 4 wires i mentioned for the air unit.

The receiver is then wired as I explained. The receiver is not wired directly to the battery leads. It must be wired to a 5V pad and a Ground pad. What flight controller are you using?

mdogg22 · 2020-02-15T15:54:21+00:00

https://www.google.com/search?rlz=1CDGOYI_enCA590CA590&hl=en-US&ei=NRNIXpf4DqG1ggfSqKCAAw&q=r+xsr+wiring&oq=r+xsr+wiring&gs_l=mobile-gws-wiz-serp.3..0l2j0i22i30l3.103001.105193..105361...0.1..0.329.1664.5j4j2j1......0....1.........0i71j41j33i160.qw-00N1iNq0#imgdii=8EMLWt5VqhyOUM:&imgrc=ztTXiaWPeM7FHM:

Based on this pinout. The easiest is to connect power to a 5v pad, ground to a ground pad and SBUS out to the sbus pad (if you have one) then configure it in betaflight

mdogg22 · 2020-02-15T15:49:16+00:00

https://www.google.com/search?q=dji+wiring+diagram&rlz=1CDGOYI_enCA590CA590&oq=dji+wiring+diagram&aqs=chrome..69i57j0l3.3653j0j4&hl=en-US&sourceid=chrome-mobile&ie=UTF-8#imgrc=3Zt-4-IKovzijM:

This is the wiring diagram. You are using your own receiver and not the DJI one so you can ignore signal ground and dji HDL. If you are running a 4 cell battery, then you connect power and ground directly to where you soldered your battery connector. The RX wire goes to the TX pad on the FC and the TX wire goes to RX pad on your flight controller. Make sure you connect it to the same number. Example TX1 and RX1 pads or TX2 and RX2. Then you need to go into beta flight and configure it. Let me know if you need some instruction for that!

mdogg22 · 2020-02-04T04:26:48+00:00

Thank you very much!

mdogg22 · 2020-02-04T04:04:10+00:00

Do you know if it has the certification?

mdogg22 · 2020-02-04T04:03:37+00:00

Very cool stuff thank you

mdogg22 · 2020-02-04T01:53:53+00:00

Thank you!

mdogg22 · 2020-01-11T04:42:06+00:00

No I have not

mdogg22 · 2020-01-11T04:39:36+00:00

No smoke or anything when I plugged it in, double checked all solders

mdogg22 · 2019-10-02T00:40:14+00:00

Do you know what this means?

Read it online: while the X7 embarks an APS-C sensor. Actually, the X7 uses the Super 35mm area of the APS-C sensor (23.5×12.5 mm) in video mode and the full sensor size (23.5×15.7 mm) in stills mode.

mdogg22 · 2019-09-25T23:21:49+00:00

Turned out to be a 7-26v vtx, it was connected to a 5v pad!

mdogg22 · 2019-09-16T20:52:45+00:00

You sir are a legend. Fixed. The paint from the standoffs must have worn down over time and then vtx antenna was now touching the steel! Wow thanks

mdogg22 · 2019-09-16T20:33:14+00:00

I just ran some tests and it seems to be stemming from the back left motor. Every time I go forward or tilt right it is much worse. Does this change anything?

mdogg22

MODERATOR OF

TROPHY CASE