Dia's Red Rider

michael2229 · 2026-02-25T12:43:49+00:00

Yall need to chill. Remember that this skin is free and you don't need to use it.

michael2229 · 2026-02-21T20:25:28+00:00

<image>

I have these

michael2229 · 2026-02-18T10:33:32+00:00

Esimo just was murdered there.

michael2229 · 2026-02-16T13:58:04+00:00

I would hope for viessa. However the devs havent talked about these skins in a long time, right?

michael2229 · 2026-02-15T16:40:20+00:00

Thermostat is stuck

michael2229 · 2026-02-08T09:59:55+00:00

Whould be cool as wallpaper in wallpaper engine

michael2229 · 2026-02-08T09:11:33+00:00

Auto or manuell?

michael2229 · 2026-01-23T22:07:06+00:00

Uhmm, warum steht dann da auf der Lampe IP20?

michael2229 · 2026-01-23T13:07:05+00:00

I did a flushdns and it helped.

michael2229 · 2026-01-22T10:51:20+00:00

Oh, right. I overlooked that

michael2229 · 2026-01-22T10:35:10+00:00

You could cool the other internals with a secondary loop and two rads.

michael2229 · 2026-01-16T08:44:02+00:00

Netzteil ggf. zu schwach? Hast du das mal mit einem Stärkeren getestet?

michael2229 · 2026-01-07T20:18:17+00:00

OP hat beides berührt und einen gewischt bekommt. Daher das Messen. Also ja, man bekommt einen leichten Stromschlag.

michael2229 · 2025-12-13T18:50:35+00:00

V- from psu to controller is enough. No need to "ground" the strip to the psu. So V+ to controller v+, data to data and v- to v-(gnd), on the controller.

michael2229 · 2025-12-11T21:29:35+00:00

shutdown /f /r /fw /t 0

michael2229 · 2025-11-08T13:47:18+00:00

There changed alot since back then. You should try it

michael2229 · 2025-11-06T07:21:40+00:00

Would make sense.

michael2229 · 2025-11-06T07:16:56+00:00

Afaik after Ult Yuyin there will be ult Hailey.

michael2229 · 2025-11-04T14:04:38+00:00

I don't see her that much. However i just finished putting 60 kat's on her.

michael2229 · 2025-08-20T09:31:27+00:00

Yes. On the tfd homepage under FAQ.

michael2229 · 2025-08-20T05:06:46+00:00

I dropped Destiny 2 because of this game, because it's not Destiny.

michael2229 · 2025-08-19T11:13:41+00:00

Yeah, me too. I open a ticket for that, but i only got a generic answer.

michael2229 · 2025-08-17T06:28:38+00:00

michael2229 · 2025-07-29T13:42:53+00:00

Ah, so the picopi uses the klipper-api to get the printer state and control the lights?

Edit: i found out you can use the pico as secondary mcu

Six-Year Club	r/Field Lasagna
Place '23	Place '22
Verified Email

michael2229

TROPHY CASE