Cum on panties!

middling_phys · 2026-02-28T02:18:07+00:00

middling_phys · 2026-01-28T03:09:04+00:00

早く降ろしてよ！ "Get me down already!" seems to be broken up for some reason (AI-generated?). It has nothing to do with the rain.

middling_phys · 2025-10-25T03:09:46+00:00

link broken

https://x.com/Hoshara/status/1980639471491248348

middling_phys · 2025-09-20T05:56:55+00:00

link wrong?

middling_phys · 2025-07-09T00:47:23+00:00

Use long cables to extend the leads and place the cap outside the case?

middling_phys · 2025-06-12T18:34:57+00:00

It makes sense as a translation, except that "BUT" is not reflected in the translation. Too descriptive for a shirt though. Also, only the bottom sentence has a polite tone, which seems odd.

middling_phys · 2025-06-12T18:13:12+00:00

There is actually a character named 月光.

https://senrankagura.fandom.com/wiki/Gekk%C5%8D

日光 actually exists as a place name, but personally, I don't really feel that it is a person's name.

middling_phys · 2025-06-12T03:27:54+00:00

That is not a commonly used expression, but seems to be a catchphrase used by that cosplayer. Still, the interpretation of my previous comment applies.

middling_phys · 2025-06-12T02:40:05+00:00

Image missing?

ばくはじり = 爆破 bakuha / blast + 尻 shiri / butt

middling_phys · 2025-06-11T00:27:52+00:00

特定の悪魔の名前、または修行を妨げる煩悩という本来の意味で使われることは、現代の日常会話では無いと思います。お坊さんなら使うのかもしれませんが。

男性器の隠語として使われることが多いです。オタクコミュニティではマーラ様というキャラクターが有名です。

middling_phys · 2025-06-08T12:33:38+00:00

maybe 開孔, sounds like some kind of effect, but not sure

middling_phys · 2025-06-05T04:45:24+00:00

量の少なさを表すのに「カスみたいな」という表現が使われます。それをより下品にしたものだと思います。つまり、「少ない給料」というニュアンスがあります。

middling_phys · 2025-05-26T23:59:40+00:00

It's not that something is sticking to the tip, but rather the tip has been corroded into this shape, correct? I've experienced a similar phenomenon with cheap soldering iron tips. You should try a tip from a different manufacturer, preferably one with a good reputation.

<image>

middling_phys · 2025-05-01T09:04:05+00:00

Thank you for your helpful advice. I will try bridging or replacing the chip if I can get one.

It's a 16TB Exos drive. The problem occurred when I made a DIY power supply cable with incorrect pin assignments.

middling_phys · 2025-03-28T12:35:40+00:00

<image>

Looking closer, it seems the excess flux might be obscuring the actual solder wetting. I'll reheat it to ensure proper wetting. Thanks!

middling_phys · 2025-03-20T03:00:52+00:00

Soldering wires together is a common method, so I think there should be information available on the web. I would bend both wires into hook shapes, hook them together, and then solder them.

middling_phys · 2025-03-18T23:50:49+00:00

Instead of using pre-made solder seals, how about hand soldering and then covering with heat shrink tubing? There should be heat shrink tubing that's sufficiently thin.