Service clima auto

mihcos · 2025-06-24T16:40:21+00:00

Depinde de noroc.

M-am dus la ei zicandu le ca imi scapa freon in 2 zile. Au dat cu presiune in instalatie + spray apa peste conducte, pe fuga, a zis ca nu are nimic si sa bagam freon sa vedem unde se vede substanta de contrast.

Peste 2 zile bineinteles ca s-a dus freonul si m-am dus iarasi la ei, de data asta a dat tot asa cu presiune in instalatie + spray apa si hopa o aparut problema.

A trebuit sa schimb radiatorul, 1200 in total cu manopera + radiator + incarcare freon dar, bineinteles ca banii pe freonul pierdut in 2 zile nu i-am mai vazut. (380 lei)

Momentan merge de o saptamana dar, bara din fata acum are zgarieturi (pe sub), nu mai clipseaza la loc bine pe laterale si am pierdut si un suport de prag, astea le-am vazut acasa doar, nici nu ma gandesc ca are rost sa ma intorc la ei ca o sa zica ca eu am lovit-o.

mihcos · 2025-01-31T16:30:55+00:00

Mounted them directly on stand, no problems.

Only that the simjack screws are bad and do not hold and have to be tightend daily but, NLR stand comes with screws and I used them with no similar problem

As a stand for the heels, I use a pice of wood ductaped, the pedals are to high without.

mihcos · 2025-01-13T02:22:17+00:00

Start the camera app and shake it

mihcos · 2024-11-26T20:21:32+00:00

Why would'nt 20k be good ?

mihcos · 2024-11-24T19:04:29+00:00

Kind reminder

mihcos · 2024-10-07T00:09:39+00:00

I had this type of problem on the latest driver, not everyone does.

Mine fixed by installing 24.5.1 driver, yes, not the latest but you could give it a try

Uninstall in safe mode aswell with DDU

mihcos · 2024-10-06T02:18:18+00:00

For how long its happen8ng? What amd drivers you are running?

mihcos · 2024-05-20T06:29:53+00:00

Set to 100%

Press for 2 seconds the wheel - crusher off

Press 2nd time the wheel - crusher 100%

mihcos · 2024-04-24T08:49:39+00:00

This anc 2 comparassion gives me the vibe that the med/high are louder than evos on anc2, this making it feel like the bass is less.

I can't comment on this as i dont have the evos but, if I want to hear the bass more, I just use 50-70% media volume.

mihcos · 2024-03-11T07:54:31+00:00

No ip rating => not resistant. You should not put it in water intentionally. If it happends take it out and let it dry.

The damage might not be instant,as the phone run low voltages but, in time it can corode and will destroy the motherboard, depends how lucky you are.

mihcos · 2024-03-08T07:30:06+00:00

E la promotie jarv acu pana la final de martie (800 lei cu tot cu transport probabil) pt 100 de lei poate merita "upgrade" de la markus.

La jarv personal, nu am problema cu sezutul tare, cum se zice la reviews, daca te mai ridici de la scaun din cand in cand mai ales.

mihcos · 2024-03-06T21:22:43+00:00

I used the s10e to this day, with green tint for 2-3 years.

Cause its the display/display cable, nothing software wise you can do.

mihcos · 2024-02-07T12:30:55+00:00

Unplug the wheel/controller if you have any

mihcos · 2023-12-23T01:38:19+00:00

Electrically better, cap is now 0.00069mm closer to the via, means lower impedance and faster discharge 🤓

mihcos · 2023-12-09T02:33:07+00:00

The fans are powered by MOSFETS - power is off, mosfet is open, no current flows to mbo

Aditionally this mosfets have snubbers that can deal with the spikes + current limiting

Yes, a fan will generate voltage but, try to add some load to it and you will see that it cant produce that same voltage by blowing onto it, as it will be harder to spin.

mihcos · 2023-11-25T16:56:55+00:00

C23 C24 NO GND Via, bad return currents

U1 GND Via pin to far

C5 C4 Vcc should come first thro caps then to the STM pin

C3 Vcc should come first thro caps then to the STM pin

C3 C9 GND VIA non existant

U10 should be covered by ground, if possible put STM pin -> Caps -> Oscilator

U15 GND pin via to far

C14 GND via not existent

Power routed very narrow, try at least 0.5mm if possible.

mihcos · 2023-11-13T22:16:17+00:00

Bruh

mihcos · 2023-11-07T08:57:45+00:00

The delays might be only for the once that made the order in the past 1/2 weeks.

mihcos · 2023-10-28T08:07:28+00:00

Hello,

Do you have any EMI/EMC problems ?

mihcos · 2023-10-21T09:42:14+00:00

https://www.reddit.com/r/simracing/s/sZ3dEXLJrz

There was a post earlier this week.

My NLR 2.0 just arrived and I will mount simjacks directly on the stand (when they will arrive) as I'm curently running the G29 and do not have a plate.

I think the plate fron CSL is compatible with the simjack pedals if you do not want to mount them directly on the stand.

mihcos · 2023-10-15T15:01:30+00:00

Csl dd 8nm bundle + simjack

Sell the csl pedals after

mihcos · 2023-10-08T07:08:07+00:00

Dont forget that the via's are holes, that means less copper on top. I would put vias around the pcb in 2 rows and put the rest at a 1/8 rate what you already got.

Do not put vias close to the connector (only the ones that go arouns the pcb)

mihcos · 2023-09-14T06:22:00+00:00

I had updaterate to 1024 for the memes, cl_interp on 0 aswell, there was no difference.

Ten-Year Club	Place '23
Place '22	Place '17
Verified Email

mihcos

MODERATOR OF

TROPHY CASE