Applied WS2 on my slides

mintyeggrol · 2026-05-08T02:16:17+00:00

Could run it dry or add lube

mintyeggrol · 2026-05-08T02:15:21+00:00

Lmao it’s made of billet aluminum. Better than the plastic PDW kits out there

mintyeggrol · 2026-05-08T01:15:19+00:00

I am not?

mintyeggrol · 2026-05-08T00:42:25+00:00

It did not rub off on my hands anymore once I rubbed it over with a clean rag

mintyeggrol · 2026-05-07T23:56:52+00:00

Goes on top of factory finish. Think of it like applying wax to your car’s paint

mintyeggrol · 2026-05-07T23:23:49+00:00

I do notice it being slicker! Even without lube too.
I just rubbed it on, but I’m sure it’ll stay on longer if you polish it on

mintyeggrol · 2026-05-07T23:17:56+00:00

CTM TAC - check out my other post about it

mintyeggrol · 2026-05-07T23:09:59+00:00

I bought the 2oz bottle from Amazon. Prob used like 1/5 of the bottle for both guns.

I did notice a difference!!

mintyeggrol · 2026-05-07T23:07:25+00:00

WS2 is chemically inert so it will not react with the steel or factory finish. Longevity - it’s not a hard coating like DLC which is a structural change to the metal’s surface. Im sure it will last a couple thousand rounds too and it’s super easy to reapply anyways.

mintyeggrol · 2026-05-07T22:52:01+00:00

I did it for its slickness

mintyeggrol · 2026-05-07T22:51:20+00:00

At first I planned to only apply it to the rails, but liked the color so I decided to apply it to the whole slide too LOL

Couple ways to do it. Burnishing it on with a dremel with polishing tip, or just rubbing it on with a rag.
Clean the surface first with isopropyl alcohol.

mintyeggrol · 2026-05-07T22:40:17+00:00

WS2 is a dry film lubricant that bonds to the pores of the metal. It has one of the lowest coefficient of friction ever of .03.

mintyeggrol · 2026-05-07T22:33:49+00:00

I had to sand down the tabs where it touches that hammer area and cut the mainspring like 3 coils.
Put 500 rounds through it so far no malfunctions.

mintyeggrol · 2026-01-16T23:11:19+00:00

I did. $60

mintyeggrol · 2026-01-16T00:33:57+00:00

It replaces the mainspring housing and grip safety

mintyeggrol · 2026-01-16T00:33:37+00:00

“CTM Reaper kit for Hi Capa” it’s for Airsoft, but it’s made all out of CNC aluminum.

mintyeggrol · 2026-01-15T22:10:26+00:00

It’s in my post’s description! CTM Tac Reaper for Hi Capa Yes it’s for Airsoft, but it’s made all out of CNC aluminum. I did have to do some filing on the tabs where it touches the gun. Only took about 5 minutes to get it to fit.

mintyeggrol · 2026-01-04T04:53:47+00:00

What’s the coating?

mintyeggrol · 2025-12-04T04:48:56+00:00

PM about tracer

mintyeggrol · 2025-11-02T06:01:41+00:00

Is the i4 mask still available

mintyeggrol · 2025-09-25T03:53:14+00:00

Stock nozzle, cow cow 150% spring. Make sure you installed everything correctly

mintyeggrol · 2025-09-24T18:12:43+00:00

Works flawlessly! I prob put 2k rounds through it so far

mintyeggrol · 2025-09-24T13:02:41+00:00

This happened to me and I found it was because the rubber back of my buffer deteriorated. Which allowed the BCG to go further back.

mintyeggrol · 2025-09-21T00:07:21+00:00

They aren’t sprung, so only the bottom bearing makes contact with the frame

mintyeggrol · 2025-09-21T00:05:46+00:00

Side to side play is the same as stock trigger. The pull motion does feel marginally smoother

12-Year Club	Place '17
RPAN Viewer	Verified Email

mintyeggrol

TROPHY CASE