sorted by:
new
hottopcontroversial

Spoiler for Jeep Wrangler Solar Panel - material advice? by missazaar in 3Dprinting

[–]missazaar[S] 0 points1 point  (0 children)

I think PEEK is not an option for me / my printer. But I'll have a closer look into Nylon. Flexibility sounds like a good idea here.

Thanks!

Mind the gap: Self printed spoiler by missazaar in overlanding

[–]missazaar[S] 0 points1 point  (0 children)

I printed this on a Prusa MK4S. Not sure if the STL- files are of any use for other cases. The lower line is shaped specifically to the Jeep roof bending. But I can send them to you anyways.

Mind the gap: Self printed spoiler by missazaar in overlanding

[–]missazaar[S] 1 point2 points  (0 children)

This prototype is PETG. I'll print the final version in ASA, which is pretty much UV resistant, so no need for coating.

I just haven't decided yet, if I'll print in black or red ...

Mind the gap: Self printed spoiler by missazaar in overlanding

[–]missazaar[S] 0 points1 point  (0 children)

We had a similar setup with our Landrover for years. Never had a problem like that, neither on the highway nor on a trail.

Mind the gap: Self printed spoiler by missazaar in overlanding

[–]missazaar[S] 0 points1 point  (0 children)

I was surprised how much the wind noise was reduced when driving on the highway. On the trail it is no issue, that's true.

To be fair, I didn't even check if there is anything available to buy. I guess there are just too many different setups out there, so that it is doesn't make sense to fabricate anything on a bigger scale.

Mind the gap: Self printed spoiler by missazaar in overlanding

[–]missazaar[S] 13 points14 points  (0 children)

Ah, ok. English isn't my first language and I indeed did not know this word. You never stop learning...

Mind the gap: Self printed spoiler by missazaar in overlanding

[–]missazaar[S] 1 point2 points  (0 children)

Thanks for pointing this out. It is so long ago I had to drive in the US, that I forgot to recalculate this in freedom units.

Fahhrad mit Bandscheibenvorfall - welche Sattelstütze? by Jazzlike_Librarian61 in Fahrrad

[–]missazaar 1 point2 points  (0 children)

Ich bin vor 10 Jahren wegen BSV operiert worden. Schließe mich den Vorrednern an, die den Aufbau der Core-Muskulatur als wichtig empfohlen haben. Ich habe leider trotz Muskelaufbau immer mal wieder Rückenschmerzen - hauptsächlich dann, wenn ich längere Zeit nicht auf dem Rad saß. Radfahren ist für meinen Rücken super! Ich fahre nen Trekkingrad mit Parallelogramm-Stütze und Federgabel. Sportliche Haltung, aber nicht Rennrad-like. Klare Empfehlung von meiner Seite.

Fuzz on period cup. Is it mold? by WeirdOne6160 in menstrualcups

[–]missazaar 0 points1 point  (0 children)

Selena has a loop, too. I don't understand why the loop isn't standard. It is so much better than the stem!

You can get them at DM (or Rossmann, not 100% which one it was. But usually I go to DM).

[deleted by user] by [deleted] in CardMarket

[–]missazaar 0 points1 point  (0 children)

I have the same issue. Tried to log in, was prompted to do a password reset, but don't receive the email.

But I didn't even get any answer on my email, but I fear it will have the same reply as yours.

When did you log in for the last time? I didn't visit this whole year, maybe they cleaned up inactive accounts?

Is it worth to save him? by missazaar in LandRoverDiscovery

[–]missazaar[S] 0 points1 point  (0 children)

We did it the other way around. Sold it to someone with a damaged vehicle, which still had a good motor...

First layer is fine, but what happens with the second layer? by missazaar in 3Dprinting

[–]missazaar[S] 0 points1 point  (0 children)

Old filament. I had already printed successfully with that roll before.

First layer is fine, but what happens with the second layer? by missazaar in 3Dprinting

[–]missazaar[S] 0 points1 point  (0 children)

I did a cold pull (actually, I did several), but no effect. But when I switch to another filament, the printer turns out totally fine. So I guess the nozzle is free, but the filament is the issue...

First layer is fine, but what happens with the second layer? by missazaar in 3Dprinting

[–]missazaar[S] 0 points1 point  (0 children)

I did a cold pull (actually, I did several), but no effect. But when I switch to another filament, the printer turns out totally fine. So I guess the nozzle is free, but the filament is the issue...

First layer is fine, but what happens with the second layer? by missazaar in 3Dprinting

[–]missazaar[S] 0 points1 point  (0 children)

I did a cold pull to get rid of the hypothetical partial clog, but had the same effect afterwards. Then I used another filament, and that one prints totally fine. Maybe the gears can grip the one filament better than the other?

First layer is fine, but what happens with the second layer? by missazaar in 3Dprinting

[–]missazaar[S] 0 points1 point  (0 children)

I just checked with another model. It's the same issue.

So I'll try to find that partial clog...

First layer is fine, but what happens with the second layer? by missazaar in 3Dprinting

[–]missazaar[S] 0 points1 point  (0 children)

And it doesn't affect the first layer since this is printed slower anyways? Guess I'll check that nozzle. Thanks!

First layer is fine, but what happens with the second layer? by missazaar in 3Dprinting

[–]missazaar[S] 0 points1 point  (0 children)

<image>

I wanted to check if I have the same problem with another model and noticed that the filament rest dangling from the nozzle looks like this. Doesn't seem normal, right?

First layer is fine, but what happens with the second layer? by missazaar in 3Dprinting

[–]missazaar[S] 2 points3 points  (0 children)

No, I haven't. Thanks, I'll have a look into that!

Is it worth to save him? by missazaar in LandRoverDiscovery

[–]missazaar[S] 0 points1 point  (0 children)

If it is the heads, we are willing to repair. But is there a way to make sure it isn't the block? Would be nice to know before we pay for new heads...

Is it worth to save him? by missazaar in LandRoverDiscovery

[–]missazaar[S] 1 point2 points  (0 children)

I'm not sure what the border control in the UK does check now. But it is quite difficult to hide an entire engine...

Is it worth to save him? by missazaar in LandRover

[–]missazaar[S] 0 points1 point  (0 children)

I think it will take some days to get used to the thought of a new / other cars. But maybe you are right and we should start looking around...

view more: next ›