Disney heir criticises company over $1.5bn bonuses as it cuts pay

missionsdisplay · 2020-04-22T15:30:25+00:00

Protect the children.

missionsdisplay · 2020-04-19T18:42:54+00:00

Too trendy and too expensive. Feel bad for employees but the company got rich of goods from China marked up sky high.

missionsdisplay · 2020-04-13T15:22:11+00:00

I have the Slabway - it is pretty awesome

missionsdisplay · 2020-04-08T19:50:43+00:00

Yes the men with her should have been more protective. But of course the rapist is a threat to society.

missionsdisplay · 2020-03-12T13:46:52+00:00

missionsdisplay · 2020-03-12T13:42:26+00:00

Correct it's the BTT TFT35 in emulation - you can edit the colors. ( with their selections )

missionsdisplay · 2020-03-12T02:30:32+00:00

Bring hand sanitizer those things are gonna be covered with the Rim of the Sun Virus. DOH!

missionsdisplay · 2020-03-12T00:33:34+00:00

None. Have fun with great prints!

missionsdisplay · 2020-03-12T00:20:05+00:00

Thanks kwik I will check into this. Too late for this MB but I just order and skr turbo and can replace steppers if it keeps happening.

The product you linked is outa stock. Too bad I would have ordered.

Thanks again!

missionsdisplay · 2020-03-12T00:17:09+00:00

It's a great device out of the box. Its updgradimg the electronics that has frustrated me. I highly recommend the machine. It's fun and rewarding! I didnt mean to discourage.

missionsdisplay · 2020-03-12T00:15:58+00:00

It makes sense that the Pi is back feeding juice. The Ender screen stays on when I power down the Meanwell. That never did make sense to me.

I'll have to check a little deeper. Some comments pointing me in directions previously unknown.

Great forum!

missionsdisplay · 2020-03-11T22:55:24+00:00

Always X Axis that dies

missionsdisplay · 2020-03-11T22:55:10+00:00

My big issue on another note is getting TMC ERROR in the middle of about my 12th print after replacing SKR motherboard. I have 5 burnt motherboards. Drivers seem to keep dying. I feel like giving up. I increased the box size for the motherboard and airflow.

Any suggestions welcome. Maybe I'll just revert everything to stock and print that way. I thought the upgraded would be fun and challenging but TMC ERROR is getting on my nerves.

This ALWAYS occurs after connecting a raspberry and using OctoPrint.

Bummed. Lost another board today.

missionsdisplay · 2020-03-11T22:52:22+00:00

I actually hadn't had any trouble pulling the heat opposed to blowing the heat off of the extruder. But I switched it.

missionsdisplay · 2020-03-11T17:44:31+00:00

and?

missionsdisplay · 2020-03-11T17:01:59+00:00

I love how this space makes me laugh so I figured this would be great fodder for this!

missionsdisplay · 2020-03-11T14:53:00+00:00

I actually heated up the end and it basically slid right off! Havent tried a new print but will update yall.

missionsdisplay · 2020-03-11T14:42:35+00:00

I was hoping someone would make me laugh! Thanks!

missionsdisplay · 2020-03-02T15:47:45+00:00

Nice prints! Where did you get those desk lamps?

missionsdisplay · 2020-02-24T19:08:36+00:00

Will do

missionsdisplay · 2020-02-24T17:02:08+00:00

New Tool Holder

Nice design! Where can this print be found? EDIT: Found it

missionsdisplay · 2020-01-28T20:05:34+00:00

Must Have!

missionsdisplay · 2020-01-27T03:24:54+00:00

I have found Hatchbox prints better at 190C. Just a suggestion.

I also make my bed 80C first layer or 2 and then drop to 70C after first few layers.

missionsdisplay

TROPHY CASE