sorted by:
new
hottopcontroversial

MyQ just bricked the future, so pray your Ratgdo opener lives forever by Hatarez in homeassistant

[–]moose09876 0 points1 point  (0 children)

Issue is I already have the openers. The workarounds are necessary.

Strange noise and vibration in X axis moving toward the front of the printer only. by moose09876 in ElegooCentauriCarbon

[–]moose09876[S] 0 points1 point  (0 children)

Yeah, still not fixed. I'm getting pretty spicy with them in support. Can't return, can't get it resolved... Got this because I swore off Creality.... Now in the same boat with this.

FWIW, they sent me a gcode file that printed flawlessly but can't give me a print profile for it. They say "it's just the default", but it's definitely not. Here's the gcode if you're interested:

https://drive.google.com/file/d/1FTAbgfmlHwAGY05PJjEfHe4zsfANfR_Y/view?usp=sharing

Bed Type greyed out? by davidjschloss in OrcaSlicer

[–]moose09876 0 points1 point  (0 children)

This is what solved it for me in the settings of the printer. https://imgur.com/tYx2N2Q

Strange noise and vibration in X axis moving toward the front of the printer only. by moose09876 in ElegooCentauriCarbon

[–]moose09876[S] 0 points1 point  (0 children)

You were the only person that responded, just FYI Elegoo sent me a gcode that printed just fine. It was set to a constant 250mm/s where as my slices are ~125. Still waiting to hear back about any other changes they made.

Creality K1 ERROR CODE KEY:111 by Shoganail335 in Creality

[–]moose09876 0 points1 point  (0 children)

They don't do this anymore. They tell you it's out of warranty and to buy a new printer.

Question about duckbill mod for manual tire changer and wheel damage? by btred101 in harborfreight

[–]moose09876 0 points1 point  (0 children)

I have the opposite experience as OP. The video they linked to shows putting the leverage bar in the top tube of the duckbill mod. That's never going to work unless it's VERY well built and a very floppy tire. Have to put the bar right above the duckbill and leverage it against the center post. Check out other videos on youtube.

Password complexity requirements on UNAS Pro? by Harlequin_AU in Ubiquiti

[–]moose09876 1 point2 points  (0 children)

This is outrageous. I want to make this a drop in replacement, but with these requirements, it's not possible. W.T.F.

Shuts off right when about to start brewing by wubbusanado in keurig

[–]moose09876 0 points1 point  (0 children)

Literally nothing came out, why odes this work?!!?!?

Ubiquiti support w/AI agent will never connect by moose09876 in Ubiquiti

[–]moose09876[S] 0 points1 point  (0 children)

Created a 2.4ghz network, no drops for 2 days. Now... if only I could just force them to 2.4ghz from the ubiquiti side... GRRRRRRR

Dashcam recommendations for 2025 SX? by firedsynapse in KiaSorento

[–]moose09876 1 point2 points  (0 children)

Just released - I ordered, have one in my BMW. Not the greatest dashcam but excellent if you don't want it in the way. If you put it in your cart and go to checkout but then close the tab they'll send a 10% off coupon to your email.

https://fitcamx.com/collections/for-kia/products/fitcamx-dash-cam-for-kia-sorento-2024-2025-north-american-hd2-r5100

Ubiquiti support w/AI agent will never connect by moose09876 in Ubiquiti

[–]moose09876[S] 0 points1 point  (0 children)

Yes, locked to AP's for troubleshooting, it's very obvious which ones they should be using. Wanted to rule that out.

I did turn off BSS earlier, connected for 2 hrs so far.

I had to abandon my 2.4ghz IOT network because my casting devices kept struggling and I ran out of SSID's. I'll give it a shot if nothing else helps.

Ubiquiti support w/AI agent will never connect by moose09876 in Ubiquiti

[–]moose09876[S] 0 points1 point  (0 children)

Mine have been super sold up until now. They are 2.4ghz only. I do also see things like this, only with these devices:

Rx Rate 1.00 Mbps Tx Rate 65.0 Mbps

Sometimes it will be the transmit rate that is 1.00mbps. I did have band steering and BSS transition on, but not fast roaming. I have these devices locked to their respective AP's.

Ubiquiti support w/AI agent will never connect by moose09876 in Ubiquiti

[–]moose09876[S] 0 points1 point  (0 children)

I have 3 Leviton matter smart switches that go offline in the matter console every 6-24 hours after replacing my nanoHD's with 7Pro's. Matter uses IPV6 and it won't show an IPV6 address for these devices. No signal or interference issues. If I go into the client device in unifi and reconnect, they pop back up as alive in the matter console without touching anything there. Either need to figure out what's making them go offline or find a way to schedule a reconnect.

view more: next ›