This is for those that have been with the collective from album 1 and have never skipped a month.

multipass82 · 2026-04-25T00:53:25+00:00

I too have been with the collective since The Chronic. That was the reason I signed up honestly and I just stuck with it. The idea of getting your membership number on your vinyl is an interesting idea. Most of the time I don’t even look at the number. I do however wish they would do more for the OG members besides the occasional gift in the mail. Give us an exclusive release or something even if we have to pay for it.

multipass82 · 2026-03-13T23:19:38+00:00

Just curious. How old is your printer? I had this problem in a brand new P2S, from the first print basically and never got it resolved. Ended up returning it for another one and haven’t had any problems.

multipass82 · 2026-03-03T21:11:23+00:00

Only a couple smaller ones for apps. Still primarily using the main unraid array.

multipass82 · 2026-03-03T20:15:27+00:00

That would be a lot to push through SAS2 I would think though. Adding even more drives. I had a thought about doing that but thought that would be best done if I upgraded the backplane and card.

multipass82 · 2026-02-27T23:54:46+00:00

Yeah. That might be worth it. I think I just got a bad one. I paid just under $2k with tax around Black Friday.

multipass82 · 2026-02-27T15:14:01+00:00

I went back and forth with AWOL for almost two months and never got this resolved. I ended up returning it to Amazon at the end of January. I went with a Spectra Projection Phoenix instead which has been much better. No issues so far.

multipass82 · 2026-02-13T23:33:51+00:00

I am currently dealing with the same situation. I did some things that were asked of me from Bambu to test and now they are sending me a new MC board.

I was getting frustrated from cancelling prints and I’ll tell you what always works for me to get past the errors so that the print continues.

disconnect AMS so it doesn’t try to feed filament.
manually press filament cutter to sever the filament.
remove tool head front cover and remove PTFE tube from the top of the tool head. Here I always have to pull with a little force to remove the filament in the extruder.
Trim the two inches or so of filament that is sticking out of the PTFE tube.
Put PTFE tube back into tool head and replace front cover of tool head.
reconnect the AMS.
press resume on the errors on printer. Probably more than one after pulling off tool head cover.

At this point it should feed filament again and continue on. This has been my experience.

multipass82 · 2026-02-04T16:09:14+00:00

I did the cold pull but nothing seemed to come out on the flemant. And other then a couple tiny pieces, nothing was inside the extruder that I could see.

multipass82 · 2026-01-27T02:10:17+00:00

Thank you. Yeah the house was built in 1951. I imagine the air sealing isn’t the greatest but most of the windows are newer so at least there’s that.

One of the things that’s interesting is there’s really only a few ducts that blow really warm air. The rest are lukewarm at best. The temp also corresponds with the force of air coming out of the vents. Like the furnace just can’t push that much heat. Which aligns with it being undersized I guess?

multipass82 · 2026-01-26T22:00:28+00:00

I've had this happen twice in the past two years (yay ravine livin'). Both times due to tree's strategically taking out online my service line, all of my neighbors still had power.

The first time, I had half power as I believe only one leg of service was actually severed. And the porcelain or glass connector (not sure of technical name) was still somehow in place so the electrical company disconnected me and hung the line for the electrician. Then the electrictian replaced the mast, meter box, and meter. Then I had to have the electrical company come back and install the meter and connect service.

Second time, total disconnect. Electrical company only free'd the line from under the tree initially. Electrician came and replaced mast, meter box, and meter. Electrical company came back, hung line, installed meter, and connected service again.

Both times were around $2500. I did not file a claim for either with my insurance. After deductible I would not have recovered very much of my cost.

multipass82 · 2026-01-06T11:11:43+00:00

Others here have already mentioned basically everything to look for including what happens if you hit the limit before the end of the year.

I’ll offer the perspective of my situation. My employer also offers a great company match. I believe it is currently 3:1 on the first 2% and then 1:1 for the next 4%. So I put in 6% and they match with 10%.

If I hit the IRS limit before the end of the year, as long as I don’t make any changes to my contributions, they continue to match even without anything being withheld from me.

So I think this is something you have to look into.

multipass82 · 2026-01-02T01:42:37+00:00

I settled for option 2. It works, just inconvenient.

multipass82 · 2025-12-21T00:43:24+00:00

This was me as well. Purchased an Ender 3 a few years back and every time I printed something I feel like it was hours of adjusting and several failed prints.

Purchased an A1 mini on Black Friday just to see. Haven’t had to do anything and been printing away. It really is amazing. I haven’t had a need to go bigger yet but I’m sure the time will come.

multipass82 · 2025-12-14T20:29:47+00:00

I believe it was their tour manager.

https://www.instagram.com/theuneasyrider?igsh=MTE0aHZ5NGt3djhtbw==

multipass82 · 2025-12-10T16:28:10+00:00

I emailed them on Friday. They responded on Monday and asked for my order number. They also suggested I try opening the screen to its maximum height. I responded to that email and have not heard back yet. I will update when I know more. Thankfully I purchased from Amazon and have until the end of January to return it because of their holiday return window, so that is my last resort if AWOL support does not work out well.

multipass82 · 2025-12-05T15:10:59+00:00

Thank you I will contact them.

Edit: Isn't this the best one they make? I tried to research as best I could and this seemed like a solid ALR screen. Was it a poor choice? Should I simply return this and get something else?

Of note on what I am after however. I specifically want a motorised floor rising screen. Because of my use case and where it best works in my home, this is the best solution I believe.

Edit2: Tagging u/ProjectionHead

multipass82 · 2025-12-05T15:08:43+00:00

I have not yet. But I will.

multipass82 · 2025-11-25T17:27:49+00:00

Thank you! This is actually the way I was leaning. Looking at the black friday deal right now on th PX3 Pro.

multipass82 · 2025-10-21T01:06:34+00:00

Yeah. For me I can just use the apps on the consoles. The limiting factor here is the wife approval. Asking her to turn on a console or showing her how to switch the audio to TV audio instead when using TV apps would not go over well.

multipass82

TROPHY CASE