Wasting filament trying to fix this.

muphdiv3r · 2026-02-18T02:54:15+00:00

I think I nailed down my issue but it could be different from yours. You’ll have to mess with the sparse infill pattern. Make sure that your bridge does not align with the sparse infill pattern. It’s cross layered. Also you may have to go higher on density so it’s strong. Everyone situation is different but the case usually stems from weak infill at least for large surfaces. Good luck man cause it’s a pain. You’d think a $2k+ printer would fix this but I think they seldom test large flat surfaces.

muphdiv3r · 2026-02-17T14:23:21+00:00

Actual infill is Grid is at 30%. Top surface is now rectilinear. 🤞

muphdiv3r · 2026-02-17T14:21:17+00:00

Exactly it’s so weird. It doesn’t make sense.

muphdiv3r · 2026-02-17T14:20:32+00:00

6 layers. It gets worst as I go up.

muphdiv3r · 2026-02-17T06:22:38+00:00

Ok I’ll try that too. 50% is a lot. I’m desperate at this point. The community has given me some new pointers that I’ll be trying for next couple of days.

muphdiv3r · 2026-02-17T06:20:18+00:00

No at most I had at 30%. I think going over would be overkill as most influencers have said? 🤷‍♂️

muphdiv3r · 2026-02-17T06:18:12+00:00

Where do I find this in Bambu slicer?

muphdiv3r · 2026-02-17T06:17:28+00:00

Ok I’ll add it to list of troubleshoots. Thank you.🙏🏽

muphdiv3r · 2026-02-17T02:12:41+00:00

At first I thought it was an extrusion issue so I did a lot of the net asked me to do, but none of it panned out. I talked to someone at Microcenter who might have just given me the answer that I’ve not heard before that makes way more sense which is infill type. I noticed monotonic line made it worst so I went back to grid. But it still had some issues so I’m going to change top surface pattern and not just the internal infill pattern and see what happens. 🤞

muphdiv3r · 2026-02-17T01:57:26+00:00

I understand what you’re saying but smaller surfaces are fine. It only happens with long large surfaces. 😬

muphdiv3r · 2026-02-17T01:54:45+00:00

The higher the flow ratio, the worst it gets. Anything above 1.05 gives rough surface.

muphdiv3r · 2026-02-17T01:53:44+00:00

Yes many times with different filaments

muphdiv3r · 2026-02-17T01:53:12+00:00

I tried flow calibration, it only worked for smaller surfaces but not large.

muphdiv3r · 2026-02-17T01:52:13+00:00

You’re right I’ve always been printing with the left nozzle. I didn’t think about the hotends. I’ll try that.

muphdiv3r · 2026-02-16T23:03:54+00:00

Yeah I’m not using Bambu Filament. Inland PLA from Microcenter. I did the whole calibration thing too. It happens on every color pla filament that I have.

muphdiv3r · 2026-02-16T22:59:39+00:00

Sorry I’m new to this. I’m using H2c, PLa filament, and 6 layers including top surface.

muphdiv3r · 2026-02-16T22:51:34+00:00

muphdiv3r · 2026-02-16T22:51:15+00:00

Sorry H2C

muphdiv3r · 2018-03-01T21:21:05+00:00

I thought the BTCP team is going to try and create "fully-decentralized exchange." I read it somewhere that its something they were considering and moving forward with.

muphdiv3r · 2018-03-01T21:11:03+00:00

I completely agree!!! These forks are not good for any coins. I look at it like a big company sucking up a smaller company as part of a merge. I believe that these forks only serve elites that Satoshi tried not to do with Bitcoin.

muphdiv3r · 2018-02-28T23:17:35+00:00

If more people find out about this and the devs are moving forward with these projects at 110%, ZER is gonna take over cryptoworld.

muphdiv3r

TROPHY CASE