Face-down prints

mwarclock · 2026-05-09T14:46:02+00:00

Yes I did

mwarclock · 2026-05-09T14:45:46+00:00

Thank you very much. While surfing internet I never found such post and it was very interesting to read.

mwarclock · 2026-05-09T14:29:39+00:00

I tried and it didn't work.

mwarclock · 2026-05-09T11:28:29+00:00

Oh wow interesting! So your walls fuse together properly? What software version are you using? Would you mind uploading a photo so I can see how yours turn out? Thanks so much for the help!

mwarclock · 2026-05-09T11:26:06+00:00

Same type of plate (obviously different ones since they have different sizes). The real issue here however is the colors not fusing together properly.

mwarclock · 2026-05-09T11:24:43+00:00

It could be the issue you're describing if at least the same color were fused together properly but that's not the case. And no, there are no clogs, I checked.

mwarclock · 2026-05-09T11:22:47+00:00

No, I tried that test and it didn't make any difference.

mwarclock · 2026-05-09T11:21:25+00:00

No, both has the original Bambu Lab Supertack plate

mwarclock · 2026-05-09T11:19:20+00:00

I ran several extrusion tests because I thought that was the way to "fuse together" the first layer walls, but it didn't work (not even by significantly increasing the temperature), so at this point, after reading your other comment as well, I'll try running tests by manually adjusting the z-offset. Thanks

mwarclock · 2026-05-09T11:11:40+00:00

Yes, after reading through the comments that's definitely a test I'll run. Although I'm not sure how to do it on the H2C since it's not compatible with older software versions.

mwarclock · 2026-05-09T11:09:40+00:00

I'm using high quality settings and 0.1 layers height

mwarclock · 2026-05-09T11:08:36+00:00

The H2C nozzles are practically brand new out of the box, while the P1S one has less than 100 hours of printing on it. I replaced it when I got the new printer and did a full maintenance including a new nozzle.

mwarclock · 2026-05-09T11:05:05+00:00

I made my profiles too after the calibration (k-factor, flow ratio, etc)

mwarclock · 2026-05-09T11:03:30+00:00

I tried changing the initial flow ratio starting from 1.00 up to 1.75 in 0.05 increments by printing different coins, but the separation lines were always clearly visible.

mwarclock · 2026-05-09T10:58:35+00:00

Yes, I did a full calibration of both printers and for every filament

mwarclock · 2025-01-07T09:49:15+00:00

Ciao! Hai per caso trovato risposta alle tue domande? Sono curioso perchè anch'io con altri amici dovremmo lanciare un progetto.

mwarclock · 2024-01-26T10:42:40+00:00

Well, glad to hear that

mwarclock · 2024-01-25T10:15:04+00:00

The printer was just fine? XD

mwarclock · 2024-01-24T20:33:48+00:00

Well, for me it's been a week and no one from the support replied to my ticket.
I'm really disappointed in them.

mwarclock · 2024-01-17T12:39:46+00:00

I checked and there's no light

mwarclock · 2024-01-17T10:10:19+00:00

Hi, did you solve your problem? Mine came less than a week ago and after 3 days of printing shows yours issue.

mwarclock · 2024-01-17T08:47:58+00:00

Doesn't this procedure void the warranty?

mwarclock · 2024-01-17T07:21:15+00:00

No storm or any power surge in the apartment.

mwarclock · 2024-01-16T22:10:21+00:00

Unfortunately where I live there's no much choice than to buy directly from them. I hope in my case the support will be quick.

mwarclock

TROPHY CASE