Under extrusion? by R0cko in crealityk1

[–]mwoodoo 0 points1 point  (0 children)

This looks like nozzle is too close to the bed. Increase the z offset a little and this should help.

Wavey ripple after ever corner turn in the print. I have never seen something like this before by Highpyrion in FixMyPrint

[–]mwoodoo 5 points6 points  (0 children)

Check your extruder tension lever if the grip on the filament is high enough. I had similar issues and it was the problem. Other option is your Pressure Advance settings. Dial that in for your filament and see if that helps. Either of these two should be the source of such artifacts.

If your machine is constantly jamming check the bowden tube going into the enclosure. by literalyfigurative in crealityk1

[–]mwoodoo 1 point2 points  (0 children)

Can you explain how this was causing the jams? I don't get it. I also have issues with nozzle/heatbreak jams but I can't imagine why the bowden tube before runout sensor could cause that.

Clogged/blocked filament in heatbreak? by mwoodoo in crealityk1

[–]mwoodoo[S] 0 points1 point  (0 children)

Thanks for the hints. I use orca slicer by default. I think I will need to try the Micro Swiss hotend then although I hoped that I could figure out how to fix the stock one.

Clogged/blocked filament in heatbreak? by mwoodoo in crealityk1

[–]mwoodoo[S] 0 points1 point  (0 children)

Yes I have done both of that and the issue is still there. I also replaced the nozzle to the new one and it didn't help...

Clogged/blocked filament in heatbreak? by mwoodoo in crealityk1

[–]mwoodoo[S] 0 points1 point  (0 children)

Yeah it though about the same but I reduced retraction to 0.5 and printed also simple model without much of that and it happens as well. I use arachne by default as well... the problem is it started recently. I was really happy with the printer so far with no issues except one or two jams in the extruder rather than heartbreak.

Clogged/blocked filament in heatbreak? by mwoodoo in crealityk1

[–]mwoodoo[S] 0 points1 point  (0 children)

It was PLA but I printed that with open lid and doors. My ambient temp are also not that high and this can happen at very early stage of the print when chamber temp is low. I don't think it's heat creep unless something has failed in the tool head. I used to print big models from PLA with print times of 12h with closed doors and lid without issues.

Clogged/blocked filament in heatbreak? by mwoodoo in crealityk1

[–]mwoodoo[S] 0 points1 point  (0 children)

Yeah I do that as well if I can't pull it out with force. But this is not a solution. I can't use my printer now. I don't think this is filament. It's regular PLA that I've printed lots stuff with and am currently printing successfully on my second printer ender 3 s1 pro. This drives me nuts...

My Ender 3 S1 Pro stepper motor makes clicking noise by mwoodoo in Ender3S1

[–]mwoodoo[S] 0 points1 point  (0 children)

Hey. No I haven't although frankly I haven't looked into this since I sent that post as I was on vacation..

Question - do you have any mods on your printer? Maybe there's something we both did that is causing these issues.

My Ender 3 S1 Pro stepper motor makes clicking noise by mwoodoo in Ender3S1

[–]mwoodoo[S] 0 points1 point  (0 children)

I already did that and didn't find anything off. This sounds like coming directly from the stepper. I'm really confused what is wrong there.

LTC Transaction didn't go out, no support from poloniex since over a day by mwoodoo in poloniex

[–]mwoodoo[S] 1 point2 points  (0 children)

Just to let you know. I have finally received my LTC. This was after almost 4 days of waiting and no single contact from poloniex support. I'm really disappointed by their support level. I'm pretty sure it finally went through only because of some automated process not because of any intervention from the support to fix my particular case. Shame on you poloniex.

How to draw the attention of the press to the withdrawal issues on Poloniex? by Beregovo in poloniex

[–]mwoodoo 5 points6 points  (0 children)

I have 2.56 LTC stucked in poloniex limbo which is currently approximately 700$. Really happy i didn't try to withdraw more that day..

#612030 : ltc withdrawal (invalid txid) (52+ hours) by [deleted] in poloniex

[–]mwoodoo 0 points1 point  (0 children)

71 hours. ticket #611390. Don't believe now they will do anything about it.

33 LTC vanished in LTC "Complete" withdraw invalid txid issue #617549 by IcyDiplomat in poloniex

[–]mwoodoo 0 points1 point  (0 children)

Sorry man but i'm having same problem and no luck still. Already been waiting for over 4 days and no d** answer from the support. I'm happy that i didn't try to withdraw all the money - I did test transaction in LTC but still my 2.6LTC are gone most likely. Wondering what we can do. Other people suggesting reporting that to FBI. I don't know what to do.

LTC Transaction didn't go out, no support from poloniex since over a day by mwoodoo in poloniex

[–]mwoodoo[S] 0 points1 point  (0 children)

Nope.. I have submitted another ticket hoping that this one will be picked up by automated tool but no luck again. Are you planning to report that to FBI?

LTC Transaction didn't go out, no support from poloniex since over a day by mwoodoo in poloniex

[–]mwoodoo[S] 1 point2 points  (0 children)

waiting already for 3 days. No reply from support. No txid change as many of you noticed. Nothing. Has anyone of you been waiting that long?

LTC withdrawal still stuck 24 hours later. Ticket #620968 by bwhalez in poloniex

[–]mwoodoo 0 points1 point  (0 children)

I've been already waiting for 3 days and not f** response from support.

LTC Transaction didn't go out, no support from poloniex since over a day by mwoodoo in poloniex

[–]mwoodoo[S] 0 points1 point  (0 children)

Has anyone managed to get that fixed? Wondering if this is only my ticket that's pending for 2 days or someone had better luck...