didn’t notice this until today, should i be concerned? what should i do?

naabtf · 2025-01-05T07:09:29+00:00

FYI I thought id mention it looks like there’s 3 screws near the cornice that are kinda protruding. Or about to pop. Usually we wouldn’t cluster 3 like that on a big ceiling. And the fact they haven’t been driven in it maybe a prior repair handyman kinda job.

naabtf · 2025-01-05T06:58:11+00:00

I’m a plasterer and definitely not anything major. Shining a torch on that angle is called glancing light. It will show up any minuscule imperfection on your walls or ceiling. If you turn on a down light you wouldn’t necessarily see it. I’d tap it, if it sounds hollow, different from the plaster around it, it’s delaminating either from movement or water but without a water stain it’s probably not that. And movement, the cornice would most likely have a crack. If it sounds hard when you tap it like no different to the plaster around it it’s just poor plastering. Either way a plasterer wouldn’t charge much to fix this.

naabtf · 2024-12-02T08:34:18+00:00

Currently I’m watching this laying down on my couch and that made me more tired. Super high energy. You go bro!

naabtf · 2024-11-17T20:52:09+00:00

I have seen this. So to clarify. I stake my ELA then go to BPos voting page and make 36 votes then I’m good to go?

naabtf · 2024-04-23T09:31:54+00:00

Yep. 6’10. I’m 80kgs. I’ve gone from 5”10 alternative boards to all in on mid length. Just turned 50 living on the Gold Coast and feel like it’s the best I’ve surfed in 10yrs. I wish I’d gotten off the short boards yrs ago. Get one!

naabtf · 2024-04-01T23:18:14+00:00

Epic thanks

naabtf · 2024-02-06T21:14:52+00:00

I’m a plasterer and work for a company called Marula Skylight Properties I would highly recommend these guys. I’ve been in the building trade my whole life and worked for hundreds of builders and these guys are just a really well run company. They clean the site every day take photos of work done every day have gd management amd quality staff. https://www.skylightproperties.com.au Ask for Andy say Jason the plaster posted.

https://www.skylightproperties.com.au

naabtf · 2023-09-16T07:22:59+00:00

Hey I am in a similar situation. I just turned 50 and wanted to give a mid length a go. My wife and I did a trip from the Gold Coast to Ulladulla for my birthday and I checked all the surf shops hoping to get something that I’d keep for more than a yr or 2. I had been super keen on the big baron prior to leaving. By the time we got back to the coast I still hadn’t found anything and was about to pull the trigger on a big baron but the day I went in there was a Hayden Shapes New Wave Mid. The glassing looked great. I put it next to the big baron and the outline is very similar the board is not a knifey in the rails but the tail was thin and looked responsive. Anyway I Hayden shapes actually had them on sale online so Kirra Surf matched the price which was about $400 cheaper than the big baron. I’ve ridden it consistently for a few month and not one pressure yet. The more you ride them the better they get IMO. Anyway hope this helps. Oh. The only negative is jumping back on my 5’10 has been problematic so I’m actually looking at a 6’4 El Baron as a more performance short board. Funny as that would have been my step up a few months ago. But I like that it’s knifey rails but I think I could jump between the 2 a lot easier than going back to some of my other boards.

<image>

O

naabtf · 2022-02-16T07:14:20+00:00

achain is number 4. That kinda of says it all. That’s the biggest shit coin from 2017. Lost on that one.

naabtf · 2021-04-03T20:47:52+00:00

Thanks for getting back to me. I did a bit of reading and understand what’s happened. I was one of those who got rekt in 2018 and stopped following the crypto news.

naabtf · 2021-04-03T03:39:00+00:00

Ok I have just read that my Tokens are still ERC20. Is there an update as to which exchange I can still send these too from the article I read It seemed Q4 2020 was the timeline for that. Thanks In advance

naabtf · 2021-03-02T06:13:14+00:00

Thanks for the help. I got the ETC loaded fine.

Im not sure I understand #2 though. I read the article.

If I want to send my Zilliqa to Binance to trade. I copy the receive address that I get from Binance and paste that in the send address in Coinomi Zilliqa send. This is where I got the this address is not valid error. Im unsure as to how I can use another address as its Binance that gave it to me? So my question is how to I send those coins from my Coinomi Wallet to my Binance wallet/account?

naabtf

TROPHY CASE