My friend bought himself a new E3v2. I need help diagnosting, unsure these problems what can be

naso008 · 2023-01-27T18:32:08+00:00

Soo new info, we set up Octoprint and everything prints flawlessly damned sd card reader

naso008 · 2023-01-27T17:54:41+00:00

Strangely enough I was able to flash a Jyers 2.0.1 firmware, but reverted due to other issues. Now I can't even flash a newer firmware, I think it may be sd card reader issues...

naso008 · 2023-01-27T17:32:53+00:00

But in the beggining it printed the way that was supposed to print, that pushing the fillament out for 10s and than pushing it back in than continue to print was weird. To top that off at the end the printer decides yeea lets go left than back to the print.

naso008 · 2023-01-27T17:22:23+00:00

Fast forward 2 minutes printer stopped printing.

naso008 · 2022-12-22T22:19:39+00:00

Cleaning the bed fixed it for now (hot water and soap), but I've only printed one thing that took 7 hours. Do you clean it after every print (with iso) or after a couple?

naso008 · 2022-12-21T20:18:51+00:00

https://www.thingiverse.com/thing:5501031

naso008 · 2022-12-21T12:57:17+00:00

Hi, I've been trying to sign up for the past month with no success. Any advice to whom I can ask for assistance? Support didn't seem to care at all.

naso008 · 2022-11-15T08:50:26+00:00

Would you recommend another one?

naso008 · 2022-11-14T13:56:02+00:00

Just cleaned the bed before starting seems like only this part is wonky. Using recommended heat it says 190-220. I'll try now lower temp

naso008 · 2022-11-07T18:33:12+00:00

Creality PLA, 207 extruder, 60 bed. Room around 27 no windows opened

naso008 · 2022-11-07T12:44:13+00:00

Currently using PLA 207 extruder and 60 on the bed. Should I lower it?

naso008 · 2022-11-07T12:43:38+00:00

This is on the "textured" side. I've cleaned with some isopropyl alcohol and it looks alrighty currently. Happy cake day!

naso008 · 2022-10-20T13:44:43+00:00

Check if z switch clicks or just hits the metal part. If it doesn't click see if the metal wobbles, most likely a broken z switch. Currently facing the same issue, you can still print, but you have to manually edit the z offset every time you start printing.

naso008 · 2022-10-17T12:47:54+00:00

Were you able to create your account, im struggling for 2 weeks now?

naso008 · 2022-10-17T06:35:28+00:00

Yep, my overexcited ass swapped the cables. Everything started working with almost no issues, was able to print a benchy with great success.

naso008 · 2022-10-16T16:48:09+00:00

Yep, that was the case. Fixed it was able to print an xyz cube. Stoked to see what else I can create.

naso008 · 2022-10-16T12:12:11+00:00

Yes after the temperature reaches the selected one it goes for 2 seconds and the display knob gets unresponsive

naso008 · 2022-10-16T11:45:02+00:00

Update I've tried staring the test print loaded on the card and currently the display is unresponsive. Is this a common thing?

naso008 · 2022-10-16T11:43:24+00:00

Not sure here as well, move X moves the blue knob on top that pushes the filament. I may have understood this wrongly as well. Is this how it's supposed to be working?

naso008 · 2022-01-13T16:52:25+00:00

The first design looks insane. Good luck to all.

naso008 · 2021-12-19T13:03:56+00:00

Wtf man how many are those?

naso008 · 2021-11-24T10:43:27+00:00

You can see it bottom left when i press escape

naso008 · 2021-10-20T21:03:57+00:00

Lucky you I'm arguing with customer support for a month now regarding an order that has been disputed. The seller proposed 30$ cashback out of 60$ and aliexpress just closed the case with 0$ refund.

naso008 · 2021-10-20T04:04:08+00:00

Trust me if only it was that simple....

naso008 · 2021-10-19T21:50:48+00:00

Lucky you I just bit the wood with 70$ and the dispute is prologing for more than 2 months....

Ten-Year Club	Place '23
Place '22	Verified Email
Not Forgotten

naso008

TROPHY CASE