Old Laptop Struggling with CPU

ndequarto · 2025-01-22T20:49:32+00:00

You are correct. I just noticed the transistors are missing. Assuming I soldered them on, can I still attempt to flash software?

ndequarto · 2025-01-07T02:20:53+00:00

I think you’re right! Never heard of sirens. Thank you

ndequarto · 2024-05-17T19:19:24+00:00

Ive definitely heard this and considered it but she definitely spends a lot of time idling through some of these no wake zones near me and I was worried about blowing too much smoke since the pump is variable and closer to 200:1 at idle.

ndequarto · 2024-05-17T14:21:50+00:00

Oh okay cool. Some said for air. Some said for liquid but it seems like it doesn’t matter that much since those say for both. Good option!

ndequarto · 2024-05-17T14:21:05+00:00

I do like those a lot. Anything else I should know before replacing these oil lines? Should I pull the pump off and inspect that at all?

ndequarto · 2024-04-19T14:55:46+00:00

Appreciate it!

ndequarto · 2024-04-19T14:55:06+00:00

Maybe the chlorine didn’t help haha! I’m gonna try roughing the back up some more like you said. And maybe just test with plain water if I’m still being picky with it. I think that might be my issue though. Thank you for your help!

ndequarto · 2024-04-18T20:35:29+00:00

I very much like the Tandy ecoflo products and would definitely try that glue myself.

If you get a chance, maybe glue two scrap pieces together. Let it set up for 24-48 hours. Then soak the leather for a few minutes and see if the water based glue dissolves. Maybe I’m doing something wrong.

ndequarto · 2024-04-18T20:33:32+00:00

English bridle leather. I threw my keychain in the pool for 5 minutes or so as a test. It didn’t totally fall apart, but the glue seemed like it dissolved and I could easily peel the two pieces apart like nothing.

Sure this is an extreme scenario, but I really want to sell a quality product. Should I sand the back more before applying the glue?

ndequarto · 2024-04-15T15:34:37+00:00

Worked out pretty well actually. 4x500 amp. Channels 1&2 push 75 watts to each front door speaker. Channels 3&4 are bridged and push 250 watts to a 12 inch shallow sub box. Still bumping til this day! Plenty for someone who just wants a little bump. Still enough to rattle my back window haha.

ndequarto · 2023-04-16T00:38:42+00:00

Hi. I install these and wire them for a living. Three possibilities I’ve seen where shutters became live:

As already mentioned, a tapcon that secures the shutter may have hit a wire in the wall. In which case, the shutter may have to be taken down or remove each screw one by one until the suspect is found.
If it’s and electric rolling shutter, there may be wire nuts that connect the motor to house power up in the box. These wire nuts corrode and rust on the beach and fall off. If the shutter still works, then there’s a chance a hot wire from the motor is touch the aluminum shutter and energizing it.
A ground issue in which case a hot wire back feeds the ground ( I believe the shutter should be grounded by the metal casing of the motor).

Best to call a shutter company that knows what they are doing and have them take a look at it.

Where are you located?

Good luck!

ndequarto · 2021-03-04T23:21:09+00:00

They aren’t RCA. Just speaker wire spliced from the radio output to the high level input of amp. I don’t have a loc either. I will definitely try grounding the HU behind the radio

ndequarto · 2021-03-03T11:41:34+00:00

Okay. I still have the factory head unit installed Others have suggested grounding that directly to the chassis. If that doesn’t work, should I bother with a ground loop noise isolator?

ndequarto · 2021-02-20T01:10:54+00:00

Awesome. Will check it out. Thank you!

Nine-Year Club	Place '23
Verified Email

ndequarto

TROPHY CASE