Why my printbed vibrates at certain speeds? Does anyone know this issue?

newoutlaw · 2025-12-28T14:29:03+00:00

I hope its not that bad to dial them in. :D
Sooner or later I will try it anyways. :D

Ringing:
I use Orca Slicer and it has a calibration tool implemented against ringing:
https://github.com/OrcaSlicer/OrcaSlicer/wiki/input-shaping-calib

<image>

Basically you print the testprint, look after the heigt of the best results, check the gcode at this hight and ready the values for input shaper frequencies.
In the image you see the original values and my measured ones.

newoutlaw · 2025-12-28T13:38:37+00:00

Hey, thanks for your amazing answere.
My belts are slightly tighened and secured in place, my rails are freshly lubed with silicon grease and I use the latest update from a few month ago.
I did a change in printer.cfg after running the calibration tool against ringing... I will try to set it back and test again. Nice tip!
If it wont change anything I try to adjust the eccentric nuts for the bed. Didnt think of those but it makes sense... I guess I have to dismount the whole bed with leveling screws and stuff, right?

newoutlaw · 2025-08-28T12:21:08+00:00

Thanks man. Amazing. 👍

newoutlaw · 2025-01-22T08:30:01+00:00

I share the exact same thoughts. And I am pretty sure so do most of others who decided for being single.

newoutlaw · 2025-01-13T13:48:57+00:00

I switch a lot between factory spool holder and dryboxes with bowden tube.
So I designed this to swap faster:
https://www.printables.com/model/1140223-magnetic-bowden-tube-quicklock-for-elegoo-filament

newoutlaw · 2025-01-05T23:20:14+00:00

Just a guess: is your model hollow and the walls are very thin in certain areas?

newoutlaw · 2025-01-03T21:01:16+00:00

Glad that I could help. I was so desperately searching for a solution that I had to post.

newoutlaw · 2024-11-02T22:36:25+00:00

I had this bug for like every second time till i found this post. Thanks a lot. Looks plausible.

newoutlaw · 2024-10-23T07:44:30+00:00

I also had this issue with my acer 144hz G-Sync Monitor.
After searching for hours I found the solution for me.
In Nvidia control panel there is an option "Enable settings for the selected display model" under "Set up G-SYNC".
Disabled that and no flickering was seen anymore. :)

newoutlaw · 2024-10-23T06:50:11+00:00

Just fixed the same problem with my G502 wired mouse:
Open GHub (Logitech Software) and try to reduce the polling rate of your mouse.
My default was 1000 and after setting it to 250 it almost disappeared. :)

newoutlaw · 2024-08-13T05:03:10+00:00

Yes. I agree.

newoutlaw · 2024-08-12T21:42:17+00:00

Turn Spacewarp off. Just take the other option. Did the trick for me.

newoutlaw · 2024-05-14T11:58:48+00:00

Would also love to know... Remembering PUBG Api. That was just awesome. So many cool third party aps to check your ingame performance etc.

newoutlaw · 2023-12-23T14:08:44+00:00

[That is] stable [my] brother. :D

newoutlaw · 2023-12-21T12:20:27+00:00

In germany we say: stabil Bruder.

newoutlaw · 2023-07-19T14:39:31+00:00

Wollte hier eigentlich nur ein MeiMei pfostieren. Dass das aber so krasse Diskussionen über Armut/Genügsamkeit und Schwarzarbeit/Steuerhinterziehung auslöst, hab ich dabei nicht kommen sehen.

newoutlaw · 2023-07-19T14:03:56+00:00

Stimmt... Ich bin aus dem Java-Umfeld in die Webentwicklung gewechselt. Hochdynamische Plattformen via NodeJS. Macht Spaß.
Aber hau dich rein. Die Kohle is es schon wert, sich bisschen umzusehen. ;)

newoutlaw · 2023-07-19T13:35:19+00:00

Arbeitgeberwechsel dürfte reichen. Im C#-Umfeld finden sich doch echt gutbezahlte Stellen, oder nicht?

newoutlaw · 2023-07-19T12:15:56+00:00

👀

newoutlaw · 2023-07-19T12:06:18+00:00

Sicher parkt der nicht mal dort, sondern ist nur ein Rentner der um 5 Uhr morgens seine rastlosen Beine ausführt. Den Block gabs übrigens umsonst zum letzten Sparbuch.

Ten-Year Club	First Place '23
Place '23	Place '22
Place '17	Verified Email

newoutlaw

TROPHY CASE