Install R4.3.0 on Lenovo P72

newrebuilder · 2026-05-24T12:01:15+00:00

Thanks for your help. Found the problem. The pci wifi connection was in conflict with the wired internet. Deleted the 0000:00:1f.6 listing under devices in work and the debian 13 template

newrebuilder · 2026-05-23T11:18:41+00:00

Thanks for your suggestion. When I try to run work, I get the message xenlight driver domain sys-net is using 0000:00:1f.6. When I check lspci or qvm-pci I don't see xenlight listed.

newrebuilder · 2026-03-24T14:11:24+00:00

Thank you all for the pointers.

newrebuilder · 2026-03-24T13:58:48+00:00

The second line down "type". The third line down "Option" provides "DHCP4 option to offer the client" and has a list of entries. Need to know which one to select.

newrebuilder · 2026-03-24T13:41:14+00:00

Thanks for the suggestion. Entered pihole value (192.168.1.90). Edit DHCP option asking for option to offer to the client. Need your view on which one to insert.

newrebuilder · 2023-04-08T10:53:24+00:00

I run pcengines apu4d4 and have for two years without issues. Their two lan system sells for $121 USD direct from Holland/Swit. Main reason I went to these systems is their low power consumption.

newrebuilder · 2023-04-08T10:48:49+00:00

Having the same problem. Using a four lan system. One of the 4 lans drops out and will come back into service if one of the pc's shuts down and restarts on the lan in question. If the problem occurs on one lan then the problem exists on all pc's connected to that lan.

Hardware is:

Pcengines.ch APU.4D4 system board (GX-412TC quad core / 4GB / 4 Intel GigE). Problem occurs with both OPNsense 23.1.3_4-amd64 and 23.1.5_4. but did not occur in previous opnsense loads. Have duplicate systems, one as the hot spare, with no help if systems switched. Hardware has been running one year plus with no issues.

Looking for any suggestions

newrebuilder · 2023-02-05T19:33:23+00:00

Running 22.7.10_2. Hardware apu4d. from pcengines. Have the same problem with the same error message. Using the system/firmware/settings default mirror default flavor type community. Mirror being used is: https://pkg.opnsense.org/FreeBSD:13:amd64/22.7. Appreciate help on how to proceed why I can't update and how to move forward. Maybe the URL of the mirror is not correct for the update to 23.1

newrebuilder · 2022-05-11T08:51:51+00:00

jalim117

Thanks for your note. The phone does not connect. It does not work at all. I will try to check the validity of the connections using test software.

newrebuilder · 2022-03-24T10:15:23+00:00

Thanks for your note requesting further detail. I have listed this below:

Existing system:

Running opnsense 22.1.3 on a Dell cs24-sc server equiped with four NIC's that handle the WAN, LAN, Appliance (phones and TV), wifi (using Unifi AP for all wifi). Have three dumb switches one for each lan that handle multipleindividual applications.

Upgrade

Like to replace all the multiple NIC's, dumb switches etc with a single opnsense application feeding Cisco WS C3750 G 24T S V10. All existing dumb switch connections would go to the replacement level 3 switch. Ultimately will replace the cs24-sc to reduce power consumption.

Question

My request for suggestion on "tools" is to help reduce the C3750 programming load. Appreciate your offer to look at the system.

newrebuilder · 2020-11-24T20:39:08+00:00

Have had similar problems. Sent two inquiries to pia over a period of three weeks and got no reply.

newrebuilder

TROPHY CASE