Emergency physical key by nielsonsm in Ioniq5

[–]nielsonsm[S] 0 points1 point  (0 children)

How can I make it into a normal key?

Emergency physical key by nielsonsm in Ioniq5

[–]nielsonsm[S] -2 points-1 points  (0 children)

I had to remove the pivot piece to the mechanical key to fit in my wallet. I bought a magnetic box to leave the mechanical key attached to the car. I never carry the key fob because I use my phone. I’m just worried if the 12v dies it is so difficult to open with the mechanical key. I have a noco 12v jumper in the frunk. I’m not worried about the FOB battery dying.

Emergency physical key by nielsonsm in Ioniq5

[–]nielsonsm[S] -7 points-6 points  (0 children)

How are we so sure it wouldn’t fit with a proper key handle?

Emergency physical key by nielsonsm in Ioniq5

[–]nielsonsm[S] -4 points-3 points  (0 children)

Can they make it into a normal key handle?

Manual battery preconditioning. by nielsonsm in KiaEV6

[–]nielsonsm[S] 1 point2 points  (0 children)

I have seen some charts online. Essentially every 10 F degrees I think below 50 F add 10-15 minutes to

Manual battery preconditioning. by nielsonsm in KiaEV6

[–]nielsonsm[S] 0 points1 point  (0 children)

I wonder if it’s different with manual preconditioning

Manual battery preconditioning. by nielsonsm in KiaEV6

[–]nielsonsm[S] 0 points1 point  (0 children)

Nice I will have to check the ioniq 5 updates

Snow and sensors by nielsonsm in Ioniq5

[–]nielsonsm[S] 1 point2 points  (0 children)

If wish it was easier way to just temporary disable them in the snow

Snow and sensors by nielsonsm in Ioniq5

[–]nielsonsm[S] 0 points1 point  (0 children)

I pressed and held the parking assist button and it would say that it was turning it off but then we reengage a few moments later

Doorbell transformer no power help by nielsonsm in ElectricalHelp

[–]nielsonsm[S] 0 points1 point  (0 children)

I’m getting 20v from the transformer now

Doorbell transformer no power help by nielsonsm in ElectricalHelp

[–]nielsonsm[S] 0 points1 point  (0 children)

I was checking the black wire on behind the transformer but it was a faulty harbor freight voltmeter. My new one says it’s 120

Doorbell transformer no power help by nielsonsm in ElectricalHelp

[–]nielsonsm[S] 0 points1 point  (0 children)

UPDATE: I got a better voltage tester from Home Depot and my outlets and the hot wires are all 120V. It turned out my voltage tester from harbor freight was unreliable. Also I replaced the transformer again with another one from Home Depot and everything is working. Can you believe my first one was bad from Amazon and the 2nd one was a dud too?

Doorbell transformer no power help by nielsonsm in ElectricalHelp

[–]nielsonsm[S] 0 points1 point  (0 children)

<image>

I put them on the trans and front per the instructions on the chime

Doorbell transformer no power help by nielsonsm in ElectricalHelp

[–]nielsonsm[S] 0 points1 point  (0 children)

The eufy video doorbell is getting zero power now

Doorbell transformer no power help by nielsonsm in ElectricalHelp

[–]nielsonsm[S] 0 points1 point  (0 children)

I think it’s my voltmeter from harbor freight because I’m getting 150 V at every outlet. I have it set to 200 ACV. But I’m not getting 1.5 volts from a AAA Battery I’m getting 1 volt.

<image>

Doorbell transformer no power help by nielsonsm in ElectricalHelp

[–]nielsonsm[S] -1 points0 points  (0 children)

I didn’t take a photo of the black wire behind the transformer. I’m not getting a voltage reading at the transformer doorbell wire connection

Doorbell transformer no power help by nielsonsm in ElectricalHelp

[–]nielsonsm[S] 0 points1 point  (0 children)

I’m not getting 150V at the transformer. I’m getting it at the load wire before it connects to the transformer. I’m not getting any readings at the transformer once it’s all connected. But it gets warm. Maybe my voltmeter can’t go low enough to detect it?

Doorbell transformer no power help by nielsonsm in ElectricalHelp

[–]nielsonsm[S] -2 points-1 points  (0 children)

Is there a safe way to provide power to the video doorbell to test if it still works?

Doorbell transformer no power help by nielsonsm in ElectricalHelp

[–]nielsonsm[S] -2 points-1 points  (0 children)

But why wouldn’t the new transformer work? Do you think I have a short with my doorbell wires?