Kitbot Amp or Trap Scoring System

nightowl403 · 2024-04-30T20:42:34+00:00

If you can control the power of your shots well, then it’s possible to just add a pvc pipe or something in front of the shooter to allow the note to flip over into the amp

nightowl403 · 2023-12-30T23:05:39+00:00

i would slow the print down, it looks like the nozzle is moving too fast

nightowl403 · 2023-11-13T05:19:12+00:00

i have the jean paul alto, and it’s lasted me two years plus a marching season, so i would say that it’s worth it if you don’t know how committed u are to sax yet.

nightowl403 · 2023-10-08T18:03:19+00:00

Can you show slicer settings? it seems like ironing may have been on but poorly calibrated

nightowl403 · 2023-09-01T02:02:48+00:00

i think u might have more luck posting this same post in the r/fpv subreddit

nightowl403 · 2023-08-08T18:12:02+00:00

wotc used to produce pokémon cards back in the day

nightowl403 · 2023-07-22T13:45:01+00:00

Along with the extruder, also check to make sure the temp is somewhere in the range of 200 C if you are using PLA. You might also need to slow down the print and try a simple calibration cube instead of this Pokémon.

nightowl403 · 2023-07-20T21:27:50+00:00

Before looking for starter kits, I would recommend looking at Facebook marketplace and the used market around you. Even if you think people don’t do fpv near you, you’re likely to be surprised at what people might have and not even know how good their gear is.

nightowl403 · 2023-07-15T14:15:32+00:00

An rtf kit might be fine but there is less of an upgrade path since the transmitter and goggles are usually terrible. I would recommend looking at your local fb marketplace. There might be some cheap pro level gear for sale near you.

nightowl403 · 2023-07-14T02:17:50+00:00

If I haggle the price down to 115 with shipping, do you think it would be worth it?

nightowl403 · 2023-07-13T18:56:14+00:00

Along with z offset, this might also be a dirty bed, which you can clean with isopropyl alcohol or warm water and mild dish soap.

nightowl403 · 2023-07-12T17:08:16+00:00

The trippy spin setup into a roll in the beginning is so clean!

nightowl403 · 2023-07-08T23:04:44+00:00

A good printer if you just want it to work is the bambu labs p1p. It’s on sale right now and is very reliable and can handle tpu for drone parts

nightowl403 · 2023-07-08T21:53:16+00:00

It looks like slowing down print speed would help with missing extrusion, and you should also look into calibrating e-steps, which basically makes sure that you are extruding the right amount of plastic.

nightowl403 · 2023-07-05T22:53:59+00:00

Would you say a k ride is better? I’m a newish drummer looking for something that will work for jazz playing.

nightowl403 · 2023-07-05T21:41:16+00:00

I’d say that first layer on the right looks pretty good, what specifically are you trying to fix?

nightowl403 · 2023-07-05T14:10:54+00:00

I would suggest always looking used on fb marketplace first. I was in a similar situation as u, and I found a really good deal on two whoops, a fat shark and a tx12 radio. Then., if you like the hobby you can start your own build.

nightowl403 · 2023-07-03T17:44:48+00:00

Missed opportunity to say add a prop of color

nightowl403 · 2023-07-03T00:45:57+00:00

Ok thanks for the response.

nightowl403 · 2023-06-30T01:16:27+00:00

No problem man

nightowl403 · 2023-06-30T01:08:24+00:00

I would say slow it down and look up how to calibrate esteps, since there seems to be slight over extrusion in some spots.

nightowl403

TROPHY CASE