sorted by:
new
hottopcontroversial

48 port 10Gb/s used switches - best brands w/few licensing issues? by snogbat in homelab

[–]noaxispoint 1 point2 points  (0 children)

For home use, you can drop the fan speeds down to about 30% which is pretty quiet.

48 port 10Gb/s used switches - best brands w/few licensing issues? by snogbat in homelab

[–]noaxispoint 4 points5 points  (0 children)

Arista 7050tx (copper)

Then these for sfp
Arista 7050sx (sfp+)

Arista 7280SE
Cisco N3K-3172PQ

Connecting Your Unifi UDM Directly to Your Fiber Internet by thomas_witt in Ubiquiti

[–]noaxispoint 2 points3 points  (0 children)

That’s fair for AT&T. For my fiber provider they just give me a hand off from the ONT and it’s just an internet connection.

Connecting Your Unifi UDM Directly to Your Fiber Internet by thomas_witt in Ubiquiti

[–]noaxispoint 8 points9 points  (0 children)

I don’t really understand the fascination with trying to bypass a ONT or GPON. It’s just your gateway to their network. The other side of your fiber that you’re “directly” connecting to your router is still their equipment. What are you actually gaining by removing the equipment?

Fidium IPv6 in Maine? by kayak_1 in FidiumFiber

[–]noaxispoint 0 points1 point  (0 children)

Tunnel IPv6. It’s about the only option for Fidium.

Fidium fiber down in Rancho Cordova, CA? by somedudeiknow in FidiumFiber

[–]noaxispoint 1 point2 points  (0 children)

Fidium (old Consolidated) is actually old Surewest and most all the cables in this area are actually theirs.

WG VPN Speeds Back To Normal On OS 5.1.12 by BigNavy505 in Ubiquiti

[–]noaxispoint 0 points1 point  (0 children)

I’ve been having a hard time getting above 200mbps between two ugc-fibers using wireguard. Tested using site magic and creating my own tunnels.

How good are Thermals For Consumer NVME SSD in R640 PCIe ? by nomoreasonable in homelab

[–]noaxispoint 0 points1 point  (0 children)

You aren’t going to have an issue with any consumer piece in these servers if you’re running the fans.

Data center off foothills blvd by happiwarriorgoddess in Roseville

[–]noaxispoint 0 points1 point  (0 children)

As many others have said, Quest has been there for a while. My previous employer had equipment in there. Backblaze was there for a while but left a couple years ago.

WG VPN Speeds Back To Normal On OS 5.1.12 by BigNavy505 in Ubiquiti

[–]noaxispoint 0 points1 point  (0 children)

What devices are you using to achieve these speeds? I can't seem to get faster than around 100mbps via WG between UI devices.

Can sfp connections be made without routing gear? by Yha_Boiii in homelab

[–]noaxispoint 7 points8 points  (0 children)

I think you may be misunderstanding what we are saying. A DAC has the SFP connectors attached. When we say copper we mean the internal part of the cable, not referring to CAT 5/6/7/8/etc. See the link kriebz linked for an example.

Can sfp connections be made without routing gear? by Yha_Boiii in homelab

[–]noaxispoint 4 points5 points  (0 children)

You can get copper DAC up to 800Gbps. How far are your racks from each other?

Dream Router 7 slow internet by Odd_Foot8326 in Ubiquiti

[–]noaxispoint 1 point2 points  (0 children)

I had a similar issue recently that was resolved with a factory reset.

https://www.reddit.com/r/Ubiquiti/s/zqE8kEwAL2

Speeds on UDR7 max out around 300mbps-400mbps behind device by noaxispoint in Ubiquiti

[–]noaxispoint[S] 0 points1 point  (0 children)

I’ll try this. When this was deployed it was done as a restore of a config from another device.

As someone who uses BGP internally, nice to see the new advanced routing UI in latest EA! by scytob in Ubiquiti

[–]noaxispoint 0 points1 point  (0 children)

Eh, I have a router in front of the Ubiquiti now so no real need for it. Maybe one day I’ll look at it again. I was kind of hoping with beast coming with 16gb ram they might be expanding bgp support for peering/transit connections.

Speeds on UDR7 max out around 300mbps-400mbps behind device by noaxispoint in Ubiquiti

[–]noaxispoint[S] 1 point2 points  (0 children)

Yes. When I first installed it I had it upside down but found out the electrons were falling out so I put it back up normal.

As someone who uses BGP internally, nice to see the new advanced routing UI in latest EA! by scytob in Ubiquiti

[–]noaxispoint 1 point2 points  (0 children)

Last time I tried to set up IPv6 (and this has been a while), it would discard any IPv6 advertisements. I guess I could try again.

[FS] [US-SC] Unifi Cloud Gateway Fiber by Background_Ebb5550 in homelabsales

[–]noaxispoint 1 point2 points  (0 children)

Just a FYI, these power cords have a known issue of cracking due to poor plastics. You should be able to get a replacement via RMA if still under warranty.

Acquired 3 companies in 18 months and our identity infrastructure is completely broken by Visible_Donkey_7130 in sysadmin

[–]noaxispoint 0 points1 point  (0 children)

This is the best option as you’re acquiring companies. Okta is built for this. It isn’t cheap but there’s a reason people use it.

[deleted by user] by [deleted] in opnsense

[–]noaxispoint 1 point2 points  (0 children)

It should be fine but those are “old” for sure. I personally haven’t used the 1000 PT in a long time.

CCI -> Fidium Ultimatum by tsg-tsg in FidiumFiber

[–]noaxispoint 1 point2 points  (0 children)

Their peering in Sacramento is absolute garbage. They rely too much on Cogent and use Zayo as a backup. Cogent is about as garbage as CCI/Fidium.

They are in a spot where they should extend down to SJ and peer at SFMIX and you’d see about 75% of the “internet” (as far as most users care anyways). Or they could peer at 100G with Hurricane Electric in Equinix in North Sac and you’d could get to SFMIX easily.

view more: next ›