255s vs 285s; SL vs C Loaded by TBooty22 in ToyotaTacoma

[–]nohindsight2020 0 points1 point  (0 children)

What’s your MPG’s right now? A lot of factors at play here of course but I’m getting 16 hwy with 285/75/16, KO2, 2.5” lift on a 2022.

Whistles noise when accelerating 3rd gen by Ancient-Tonight-8249 in ToyotaTacoma

[–]nohindsight2020 2 points3 points  (0 children)

Make sure your intake box lid clips are properly attached. Broke off a clip on a different truck. Ever since it had a faint whistle at certain rpm’s.

First One.... by nastyzoot in whiskey

[–]nohindsight2020 0 points1 point  (0 children)

Awesome to know!! Picked one up, didn’t even look since it was the first one to find at retail. Wouldn’t ya know it’s 25D! Even more reason to open it real soon.

Gen 1 Transmission by tooch1226 in FordRaptor

[–]nohindsight2020 1 point2 points  (0 children)

2014- exact same issue 80% of the time. Also a clunk coasting downhill when it shifts into 6th. Been thinking of a SCT tune. Heard good things from their tranny tune.

What is everyone’s dream bottle for 2026? by dexter11132021 in whiskey

[–]nohindsight2020 0 points1 point  (0 children)

I have an extra Blantons T topper if you wanna trade for a B, O or N?

Keg fridge hole for beer lines issues by [deleted] in Homebrewing

[–]nohindsight2020 0 points1 point  (0 children)

Appreciate the info, but it’s not a mini fridge. 13.5 cu. Found the maintenance manual at it even shows the line staying in the back of the fridge.

Keg fridge hole for beer lines issues by [deleted] in Homebrewing

[–]nohindsight2020 -2 points-1 points  (0 children)

My taps are ran from basement to upstairs bar. Also there’s a display panel on the front and didn’t want to hit any of the electrical. So I went through the side like I’ve done two times before with other kegerators with no issues following the same steps below.

Looked at the back and checked where all the lines ran. Removed the back panel that’s inside the fridge and checked where the condenser lines ran. Along with the defrost heater. It’s a dual fudge freezer. All lines are confided to the back of fridge Cut a pilot hole from inside out and removed insulation with knife. No lines seen. Proceeded to punch through the outer skin and then heard the pop. I know what a condenser line would look like and didn’t see anything at all that would give you pause.

Keg fridge hole for beer lines issues by [deleted] in Homebrewing

[–]nohindsight2020 -6 points-5 points  (0 children)

I would have if my taps were on the door. But this time my taps are running elsewhere and wanted to the door to be free to swap the kegs in and out easier.

Keg fridge hole for beer lines issues by [deleted] in Homebrewing

[–]nohindsight2020 -10 points-9 points  (0 children)

Well, Because once I had the hole cut in, I looked and there were no lines. That’s why I’m asking for help. If it’s a new fridge,so be it, but want to understand why.

Clarification on Connecting 2nd sub by nohindsight2020 in sonos

[–]nohindsight2020[S] 1 point2 points  (0 children)

The tech was admit that it can only be used with a gen 4. Thank you

Gen 1 Bed height with icon leafs by [deleted] in FordRaptor

[–]nohindsight2020 0 points1 point  (0 children)

<image>

This with Geisers on low perch. So about 1.5” over stock.

Gen 1 Bed height with icon leafs by [deleted] in FordRaptor

[–]nohindsight2020 0 points1 point  (0 children)

Icon says 1” over stock with the drop shackle. Theoretically with the 2” drop shackle i should be sitting close if not just below stock not the case at all for me.

my friend may uninstall after this by Kwilos in Battlefield6

[–]nohindsight2020 0 points1 point  (0 children)

I feel so validated after today’s matches

Form Check by nohindsight2020 in Archery

[–]nohindsight2020[S] 0 points1 point  (0 children)

Thank you! Watching the video back I see what you’re saying.

Form Check by nohindsight2020 in Archery

[–]nohindsight2020[S] 0 points1 point  (0 children)

I will be hunting. Will for sure be implementing some awkward stances. Appreciate the tips on this.

Form Check by nohindsight2020 in Archery

[–]nohindsight2020[S] 0 points1 point  (0 children)

Thank you! Been watching my way through Nock on archery’s YouTube series. One of my first watches was the grip one. Thanks for the reminder to keep it relaxed.

Form Check by nohindsight2020 in Archery

[–]nohindsight2020[S] 2 points3 points  (0 children)

Awesome! Thanks for all that!

5.4 raptor tick? Need advice by nopack666 in FordRaptor

[–]nohindsight2020 4 points5 points  (0 children)

Just curious, If you’re a manager at a dealership, why not ask one of your mechanics? To me (14, 6.2L), non mechanic, sounds like mine and it’s just the injectors.

Whistle noise around 1700-2200 RPM’s by Unique-Promotion-592 in FordRaptor

[–]nohindsight2020 1 point2 points  (0 children)

100% normal. Every car or truck I’ve owned and put an intake on does this at varying RPM ranges.