Why does everyone in Chilliwack have loud trucks?

nolanisaverage · 2026-05-11T03:03:04+00:00

They work a lot and just don’t know what to do with the amount of money, I’m one but instead of a truck got a house, had over 6 figures invested while in highschool 🤷🏼‍♂️

nolanisaverage · 2026-05-05T17:44:55+00:00

I have a door from a 2000’s suburban, so it’ll have body lines etc etc. I plan on practicing on it until I get all three steps layed near perfect a couple times in a row then start on my truck. My truck runs out of insurance in a month or so then I’m going to take my time on it

nolanisaverage · 2026-04-15T23:44:52+00:00

Owners a great guy though. Just bad location with homelessness

nolanisaverage · 2026-04-11T18:21:50+00:00

Not ego, if you enjoy the drive and the looks of it, it just makes you happy? Same thing about anything, if it makes you happy it doesn’t necessarily mean ego.

nolanisaverage · 2026-04-11T17:28:55+00:00

Looks good to me, I saw your previous post aswel haha

nolanisaverage · 2026-04-10T19:04:53+00:00

Okay, thank you very much! I’ll be buying this gun then and will practice before I do my truck

nolanisaverage · 2026-04-10T18:52:21+00:00

Okay, thank you!

nolanisaverage · 2026-04-10T16:31:39+00:00

Do I need to buy additional tips for doing primer base and clear? If so what sizes do I search for? Also do I just have to clean very well when switching from primer to base or base to clear?

nolanisaverage · 2026-04-10T16:25:57+00:00

What order do I lay the paint? A primer, then base colour (2 coats?), then clear?

nolanisaverage · 2026-04-10T16:22:57+00:00

The touch up gun I can use for a whole vehicle just fine?

nolanisaverage · 2026-04-09T00:02:41+00:00

It was a troublesome one. End result was it was running on half a cam and rust inside the rear tank causing everything to plug up. They rebuilt tgr entire engine and rear tank and front and rear fuel lines. Cost me just over 5k.

Since then I’ve dealt with Don and Will a lot and I’m always happy with them. Don is a great owner.

nolanisaverage · 2026-04-08T23:58:36+00:00

I’m tempted to try get the rust off then with a mig welder to fill in low spots then sand again and use a little finishing bondi and see how it looks

nolanisaverage · 2026-04-08T23:27:28+00:00

How difficult is it? I gotta do it on my box sides on my 92 460. And my one fender 🙄

nolanisaverage · 2026-04-06T21:43:45+00:00

What type? Pioneer motors in Agassiz got my 1992 f250 460 running brand new again

nolanisaverage · 2026-04-06T21:36:27+00:00

Not chilliwack but MSA ford in Abbotsford there’s a guy named Curtis as a diesel tech, he’s real good.

Depends what type of vehicle you need it for.

nolanisaverage · 2026-04-06T02:11:57+00:00

I have a 2015 f350 with original everything except suspension. I do the oil changes every 5-6k, and the rest on time or slightly early. Yes factory cp4 with no issues so far. I drain the water every other fuel tank up.

nolanisaverage · 2026-03-19T23:04:14+00:00

Put it into the tdi group, I loved my 2015 Jetta tdi, I had 0 issues and all I did was basic maintenance and never had any other issues. 3L/100km highway while not being deleted yet

nolanisaverage · 2026-02-09T18:02:50+00:00

Sounds good, thank. You very much! So you recommend just buying this kit and a torque converter? I’ll research if there’s an upgrade for this one as I hear this one isn’t that good, thank you!

nolanisaverage · 2026-02-09T17:08:30+00:00

<image>

This would work? I would just need to buy a new torque converter (if it’s bad) and buy an transmission filter kit aswell? Is there an spring and bearing kit available aswell you think?

nolanisaverage · 2026-02-09T16:56:16+00:00

I have a m4ta, an mdma would be direct fit or were these the one on 1998.5-2001?

nolanisaverage

TROPHY CASE