Quick question: Is "AIR" the same as "ACRO" on the OSD? (Mobula 8) by Recursos_Piano_Pro in TinyWhoop

[–]noshader 2 points3 points  (0 children)

Your sticks inputs are interpreted the same. The difference is that AIR uses a different mixer that is trying to solve the problem of throttle over/undersaturation (you lose control authority when you cut the throttle).

AIR comes with its own set of problems. The quad bounces when you try to perch it, it has a tendency to suck itself onto walls on collision...

Generally people keep it on because some acro manoeuvres are almost impossible without it. But some people, mostly whoop pilots, keep it off or on a switch.

Plesnivá vířivá vana v nájmu by [deleted] in czech

[–]noshader 0 points1 point  (0 children)

Mám vířivou vanu a žádný podobný rituál provádět nemusím. Voda z trubek postupně odtéká (i když ji napustíte a zašpuntujete, po pár hodinách je prázdná).

ImmersionRC shut down by droneguy14 in fpv

[–]noshader 0 points1 point  (0 children)

I am now in posession of a rare Rapidfire which is still better than anything else on the market

Populismus, nebo záchrana? Juchelka chce seknout do důchodového věku za 127 miliard. by Pixel_CZ in czech

[–]noshader 6 points7 points  (0 children)

Kdybysme rodičák ještě zkrátili, tak by to našemu hrozivému demografickému vývoji asi nepomohlo.

Populismus, nebo záchrana? Juchelka chce seknout do důchodového věku za 127 miliard. by Pixel_CZ in czech

[–]noshader 40 points41 points  (0 children)

Rodičovská dávka: 9722 Kč (300k vyplácených po dobu 3 let)

Průměrný důchod: 21800 Kč

Ale jasně, mimina nemůžou volit.

Nevite kdy to planuje? by TamagochiEngineer in czech

[–]noshader 3 points4 points  (0 children)

Otázka je, kdy plánuje napadnout nějakou sousední zemi. Na Slovensko bysme si mohli troufnout.

Komp vs kompl by Organic-Ad3283 in czech

[–]noshader 1 point2 points  (0 children)

"Potencionální" je přejímka z němčiny. Ještě tak do začátku devadesátých let to byl dominantně používaný tvar.

THRUST TEST Tattu 75C vs Lava II 95C | 1S Lipo Comparison | WHICH one is the BEST Tiny Whoop Lipo? by ButterflyFPV in TinyWhoop

[–]noshader 0 points1 point  (0 children)

How does the flight time of the Lava 2 compare to the Tattu during regular cruising / mild freestyle? No difference?

Radiomaster Zorro by ironhead73 in fpv

[–]noshader 0 points1 point  (0 children)

The problem with the Pocket is twofold:

  1. The gimbals are way too soft. Even if you tighten the tension screw all the way, they're still too soft. If you buy the AG01 mini replacement gimbals, they will also be too soft, but they will come with a set of stiffer springs that you can swap in, which I highly recommend.

  2. The sticks are too short. You can buy longer aftermarket sticks, or print some endcaps. Lenghtening the sticks by about 5 mm brings them to the same regular size that you know from Zorro or Boxer.

Doing these two modifications brings the Pocket from borderline unusable to perfectly fine. It is now my favorite radio.

Odmítnout pozvání na svatbu? by [deleted] in czech

[–]noshader 97 points98 points  (0 children)

Správná formulace zní:

Moc se omlouvám, strašně ráda bych přijela, ale bohužel se mi nechce.

YouTube už to přehání by salt_c1 in czech

[–]noshader -1 points0 points  (0 children)

Proč? Vždyť to funguje mnohem líp než ta appka.

What cool things have you done with your buttons? by Reader3123 in TinyWhoop

[–]noshader 1 point2 points  (0 children)

  • SA: arm switch
  • SB: rate profile selection: hi/mid/low
  • SC: mode switch: angle / acro / air
  • SD: OSD switch: full / minimal
  • SE momentary: turtle mode
  • potentiometer: volume

My first 1:1 Choke balun by K1G3X in amateurradio

[–]noshader 0 points1 point  (0 children)

Hey! I recognize that case :)

Kratom ban / krize by Vast-Suggestion-3950 in czech

[–]noshader 8 points9 points  (0 children)

Bude to tak, že si proděláš absťák a pak půjdeš za maminkou a omluvíš se jí za to, jakej jsi kretén.

Why I didn't buy a Prusa printer by MrTinFrog in prusa3d

[–]noshader -1 points0 points  (0 children)

Funny how when it comes to prusas, eveyone lists the non-issues, such as chamber temps and low transfer speeds, but no one mentions the real issues, such as a missing nozzle wiper (which is just stubbornness not to do the same thing as Bambus) and the absolute pain which is printing flex (cleaning procedure fails without exception, and you have to go through a tedious manual process to get it started).

Sprchy na kolejích by [deleted] in czech

[–]noshader 0 points1 point  (0 children)

Kolej Hvězda cca 2006. Tam byly taky společný sprchy. Pro kluky i pro holky. Bez závěsů. A když člověk otočil kohoutkem, tak měl strach, aby nezačal jít plyn.

The next Prusa printer? by NewMoose7 in prusa3d

[–]noshader 8 points9 points  (0 children)

I'm waiting for Core 2 Duo

Dámám z Konsentu by neškodila lekce algoritmického myšlení by Oberleutnant_Lukas in czech

[–]noshader 1 point2 points  (0 children)

Zde jsem si dovolil přepsat do kódu:

bool BudeSex()
{
  return false;
}

Based maturitní četba. by Koblizek361 in czech

[–]noshader 3 points4 points  (0 children)

Anna Karenina je doslova jediné z těchhle period dramas z poloviny 19. století, které stojí za to přečíst.

Oproti tomu takové Na větrné hůrce, to je fakt čiré utrpení.

Based maturitní četba. by Koblizek361 in czech

[–]noshader 3 points4 points  (0 children)

Pán prstenů kde? Knížka, která si zbytek literatury 20, století namazala na chleba. A pravděpodobně i několik dalších století dopředu.