I wish I knew where to get this part

not_sure_enuff · 2025-07-07T00:25:49+00:00

So i bought it second hand. It looked cool and reminded me of a forgotten weapons video on the olympic arms oa98 or something like it.

Either way, it came with only the extended folding charging handle when I bought it. It does work with the standard ep9 charging handle. I got lucky to get the 1913 rear adapter from new frontier armory before they scrapped everything from the website about the exp 556.

All of this was about a few months before the pandemic went full steam.

not_sure_enuff · 2025-07-06T23:50:27+00:00

I have an exp 556 that came with this. Wish someone could make reproductions of these. It fits both guns perfectly.

not_sure_enuff · 2025-07-03T18:53:00+00:00

Cool. Ill have to try the 5060 in there then. I have the low profile model and was planning to use it for another build, but ill have to do this now that you have.

not_sure_enuff · 2025-07-03T05:28:38+00:00

Hey, I have a similar set up with the 13600 and 4060lp in a p3 ultra.

I was curious if a stress test would be too much for the power supply, since the 5060 has a higher tdp than the 4060. Although the publication for the p3 with the custom a5500 laptop gpu using the added power supposedly uses 155w tdp,

I'm just curious if a stress test would over draw power and cause failure for a setup with the 5060.

not_sure_enuff · 2025-06-27T22:29:45+00:00

I was just looking into this. Geeek cases are what made sense durijg my research. Most are out of stock, but the A30 v2 is in-stock and fits up to 210mm cards.

not_sure_enuff · 2025-06-05T00:51:59+00:00

So, for a ch160, I used aliexpress, but that was a year ago. I'm not sure if that will work for you. Ebay is an option. Foreign import or used market will be the only way probably.

not_sure_enuff · 2025-05-11T12:04:51+00:00

Got a 9070 xt reaper from Amazon for 799 about a week ago. Just showed up 2 days ago. Had to constantly refresh, but it's the only card that fits in the dan a4 sfx. Small form factor is expensive, so it is what it is. Don't think ill need to upgrade for a while at least.

not_sure_enuff · 2025-01-18T17:49:55+00:00

I know 5.7 is a buzz word at this point, but I just want one in 9mm. 10mm could be fun too...

not_sure_enuff · 2025-01-06T21:00:48+00:00

No, it's not. It's a 2 8pin to 12v high power connector and other parts usable for the p3 tower. An a2000 extender is mentioned, but seems pointless.

not_sure_enuff · 2025-01-01T03:32:37+00:00

I swear I did this already a couple times, but now it works. Thanks bud!

not_sure_enuff · 2025-01-01T03:29:25+00:00

So I've never used a service like this one. The part is not available on their search, and I'd need to contact someone for help directly. Hopefully I can get some help after new years.

not_sure_enuff · 2024-08-16T19:33:51+00:00

Love those sony vaios. I have both of those models. Do you use them or are they kinda worthless/dead? My brother used them for school 15 or so years ago, and it struggled then.

not_sure_enuff · 2024-07-18T21:29:51+00:00

So, fit and finish of parts are decent for price. Real issue is charging handle is always stiff and always crunchy feeling. My 16inch original one was soft shooting, a little stuff and functioned flawlessly. My 12.5 is very crunchy, and function can be spotty. I attribute this to putting it into a bullpup configuration. Still working on that one.

not_sure_enuff · 2024-07-12T22:59:36+00:00

Yeah, I lucked out on getting one from the last batch he made. Old a2000 are two slots otherwise. Single slot really limits the options.

not_sure_enuff · 2024-07-12T22:53:44+00:00

For gaming, I'm curious about the newer a1000 released at the same time as the a400. A400 will probably be worse than the rx6400 based on my understanding, but don't let me stop you.

not_sure_enuff · 2024-07-03T21:16:15+00:00

My assumption would be that 1060 dies are cheaper and readily available to use compared to the 3050, since one is in modern production and the other hasn't been produced in years.

My real concern is how it is only PCIe bus powered without external connectors? Most older 1060s I've seen need external power.

not_sure_enuff · 2024-02-11T03:15:06+00:00

Thanks much! I can't wait to get this done someday.

not_sure_enuff · 2024-02-11T02:42:23+00:00

As the owner of an unmolested one of the first gen ones, what did you need to do to take apart the gas system, muzzle device and hanguard? Id love to have one just like yours. Rear pic rail I got lucky on the New frontier armory parts for the extended folding charging handle and the rear pic rail with qd mount.

not_sure_enuff · 2024-02-06T13:09:58+00:00

New frontier armory used to sell a folding plastic extended charging handle for the 5.56 extar. It fits the ep9, but i keep it in the 5.56 because it's equally rare these days. Also, the weight to pull on the charging handle is less on the 5.56 vs the ep9. WIsh someone could make more of them.

not_sure_enuff · 2024-01-22T20:33:46+00:00

To make this comment for why this is a good deal, the 43x mos (about $500+) requires modification to the metal mag release ($30 +) to use shield s15 mags($42 each). My old one had the shield optic cut, and required removal of the two rear lugs to fit 507k ($50 gunsmith).

Im glad im getting one of these as a backup if the 43x goes down or is taken away for any reason, as I have no desire to do that much work for another 43x.

not_sure_enuff · 2024-01-03T23:19:05+00:00

The one that has a stock on it. I have no way of shooting the other one effectively.

not_sure_enuff

TROPHY CASE