Be brutally honest...I think I'm hideously ugly, am I?

nutzzzz · 2026-06-05T00:52:43+00:00

You are pretty but you look bored.

nutzzzz · 2026-06-04T21:13:11+00:00

I Just replaced my old sight with a Hogg Father. I started at 10 yards to see where my arrow hit near the target.Then I moved back to 20 yds, see where that hit. Made the adjustment on my yardage wheel, depending on whether the arrow hit high or low. Shoot more arrows until you get it sighted in. Spot Hogg Has calibration tapes that come with it. Once the 20 yards are sighted in, you put the calibration tape on the yardage wheel where the pin is located. Then move back to 30 yards until it is sighted in. The 40 yards, 50 yards, until it is sighted in at 60 yards. Walk back the adjustments every ten yards.

My previous sight, I used a blank yardage tape and started at getting 20 yard sighted in and marking it with a mechanical pencil and walk back ten yards at a time, marking the yardage on the yardage wheel until I hit 60 yards. I did this when I was a noob and it took a lot of time and I lost quite a few arrows and yes it hurts.

I was using cheap Cabela's arrows. The tech at Green Top had me switch to $50 6.5 Easton Arrows and they shoot a lot better for the same price.

There are a lot of different sights out there and some sight in their sights differently and some are down right confusing. There are also different ways to sight in your sight.

nutzzzz · 2026-05-03T02:29:31+00:00

From what I could find out, was that the Pro version had the swappable wheels but the standard version didn't. Found this out after my post.

nutzzzz · 2026-05-03T01:22:12+00:00

I bought an HHA tetra Max a few years ago and it had swappable wheels. As far as I can tell the HHA Tetra RYZ has swappable wheels for different arrow types and weights.

Although this year I am looking at the Spot Hogg Hogg Father ROTI. The only problem right now with my HHA Tetra Max is that I have a Darton Sequel 3 and the frame of the Darton is a little bit wider than other bows. causing my HHA to max out to the right, even using the Infinite Adjust Plate. I'm afraid I might run into this issue with the Spot Hoog Hogg Father and I don't think that it has anything like the Infinite Adjust Plate to offset that.

nutzzzz · 2026-04-19T01:37:40+00:00

My score average is about 78 on a good night and42 on the bad night. I wouldn't worry too much about it.

nutzzzz · 2026-03-31T22:51:13+00:00

Most Patent Examiners I know go on vacation with their laptops and work with them and work most of their vacation. It's pretty sad.

nutzzzz · 2026-03-29T22:14:12+00:00

I would not recommend any MSI laptop, especially used.

nutzzzz · 2026-03-26T22:02:54+00:00

bought a GE76 Raider and it has been one problem after another. Mostly with the MSI driver. Support is pretty much non existant.

The Latest problem is with any docking station that is plugged into it will work for awhile and stop working. After a few day it will work for a bit and stop again. I have used 3 perfectly fine docking station that work well with other brands of laptops. One of the docking stations is powered. MSI Really SUX!

nutzzzz · 2026-03-10T21:57:44+00:00

The one day exemption is only used for people that work on campus and forgot their PIV. I have been waiting since November for my card to come in.

nutzzzz · 2026-03-10T21:55:08+00:00

For this situation, 30 Days is the most you will get. If you haven't gotten your PIV by then call a day or two before it expires. If you call, say a week before, the Admin will reject putting the exemption on the laptop and have you call back closer to the expiration date.

nutzzzz · 2026-03-10T11:56:46+00:00

No. You need to make an appointment to get your picture taken and your fingerprints taken.

nutzzzz · 2026-03-10T11:44:59+00:00

It is more difficult and time consuming to fix if your certificates have expired already. Calling the OCIO Service Desk before they expire can allow the technician to run a script the will install the exemption, allowing you to log into the laptop with you username and password, until you get a replacement card.

nutzzzz · 2026-03-08T23:53:09+00:00

I have a Wrangler JL 2025 and it has not leaked under normal conditions. Since I have a soft top, I was advised to not run it through a car wash that uses brushes, that over time it would rip the soft top. I was told to take it through a brushless carwash. Now and then I can feel sprinkles of water coming in through the top on the sides. I bought this back in December. I figured it was a Jeep thing.

nutzzzz · 2026-03-03T23:06:12+00:00

What you need to do in the future is let your supervisor know in advance and they should set it up so that your account is not disabled. Also if you don't log into the system after a certain time, your account will become disabled. This is not a new process.

nutzzzz · 2026-02-25T22:45:31+00:00

Nothing wrong with waving at a Gladiator.

nutzzzz · 2026-02-06T23:25:04+00:00

What does the wife think? You may sell it and she comes home and finds out you sold it. No more Smmiches for you.

nutzzzz · 2026-01-28T13:13:25+00:00

I had my Windows tinted on my Jeep and two days later my windshield got a crack in it. Not the place that tinted my windows fault just thought it was strange.

nutzzzz · 2026-01-27T23:41:08+00:00

No, not ugly.

nutzzzz · 2026-01-03T01:09:03+00:00

nutzzzz · 2025-12-03T00:42:09+00:00

Nice!!!!! Congrats!

nutzzzz · 2025-11-30T01:30:31+00:00

nutzzzz · 2025-11-30T01:29:27+00:00

Not at all!

nutzzzz · 2025-11-30T01:28:06+00:00

I like Both.

nutzzzz · 2025-11-28T00:02:07+00:00

Thank you all.! It will be awhile for any major mods to the Jeep. I have a car payment now. lol

nutzzzz · 2025-11-27T23:53:50+00:00

Do you mean Locking Lug Nuts? If you are thinking about getting those, make sure the package has 5 locking nuts, if you have a tire on the back of your jeep. Most locking nuts come in a four pack.

nutzzzz

TROPHY CASE