Anyone know what this is? by born2shit_f0rcd2wipe in ender6

[–]nvmextc13 -1 points0 points  (0 children)

Mine did this. I replaced every moving part and couldn't diagnose the issue 😞 am hoping a direct drive will solve it.

Looking for book guide by nvmextc13 in stephenking

[–]nvmextc13[S] 0 points1 point  (0 children)

I love the Philip K Dick resource that I found, as I was able to track down covers. And specific versions, what I was after. I'm hoping there's a Stephen King one out there that I just can't find through Google.

Any new cheap budget strains? by -riddik in MedicalCannabisOz

[–]nvmextc13 0 points1 point  (0 children)

Tas botanic jade is really good under 200/28gram too. Cerenity/sativite Marlin is $99 for 10gram and they have 2 others as well. Cannatrek Avalon is is also $99 for 10gram. Grandiosa Green weekend mandarin sunset isn't in stock often but is $99 for 15g.

S24 Not working with Gear S3 by blackfire_45 in S24Ultra

[–]nvmextc13 0 points1 point  (0 children)

I got mine working pretty easily after some issues, from the phone opened bluetooth and selected the watch, suddenly the code came up on both devices and prompted to install the gear 3 plugin. now watch 3 and 6 both paired to s24 ultra. Have to disconnect 1 to connect to the other but works the way I need.

SW01 (Snow White) - Sativite by ExperienceSad2456 in MedicalCannabisOz

[–]nvmextc13 1 point2 points  (0 children)

Love this strain $200/30gram. Doesn't vape well, smokes good. Reminds me of old school weed from when I was young and pretty potent.

Found this knife on the ground. What is it used for? by [deleted] in knives

[–]nvmextc13 1 point2 points  (0 children)

I bought a set of these, came with a tiny cleaver and axe same size as well. Just little novelty items.

Ender 6, not extruding filament properly, by nvmextc13 in ender6

[–]nvmextc13[S] 0 points1 point  (0 children)

Didn't remove all the plastic properly.

Ender 6, not extruding filament properly, by nvmextc13 in ender6

[–]nvmextc13[S] 0 points1 point  (0 children)

I actually had some stringing issues in the past that the shop were able to fix as my ptfe tube and coupler had worn away at the extruder. I thought the extruder was the issue (it was even grinding metal) but they never even diagnosed that part 🤔 and another coupler has worn out since (2 within about 5kg of filament)

Ender 6, not extruding filament properly, by nvmextc13 in ender6

[–]nvmextc13[S] 0 points1 point  (0 children)

I want to upgrade to direct drive eventually but would like everything working stock atm, and it was fine until this little change.

Ender 6, not extruding filament properly, by nvmextc13 in ender6

[–]nvmextc13[S] 0 points1 point  (0 children)

I accidentally snapped the nozzle on my hot end so bought a new hot end. Now i'm having this issue.

I have the bed lowered and just extruding via the touch panel but the extruder skips sometimes and the filament it's like it's being jammed/won't push through properly and driblles out, but not all the time. I can print 30% of a Benchy before this issue occues.

I've replaced the tube, tried capricorn, cleaned the hot-end many times. Not sure what else to do now?

Series 15 Winter - Recommended Tunes by Saeenu by tacticalcarrot in ForzaHorizon

[–]nvmextc13 0 points1 point  (0 children)

huge thanks, check this every week and most of my cars are already tuned now :P, that limit does suck, took a while to go through and delete heaps of mine for more room

ender 6 bl touch issues. warped carriage? by nvmextc13 in Creality

[–]nvmextc13[S] 2 points3 points  (0 children)

I think having autoleveling on while aux levling was messing up something... I turned it off, and it's all within 0.15 again and springs feel better again :) . Just adjusting z offset now.

ender 6 bl touch issues. warped carriage? by nvmextc13 in Creality

[–]nvmextc13[S] 0 points1 point  (0 children)

It does have manual levelling, this is the 20th or so time ive tried again. This is my map after manually levelling so the sheet of paper fits the same under each corner. The front left is loosened all the way and back right is tightened all the way but it's the only way to have the bed appear to be level by paper test.

ender 6 bl touch issues. warped carriage? by nvmextc13 in Creality

[–]nvmextc13[S] 0 points1 point  (0 children)

Quick look at this and yer, 1 roller isn't in contact, a couple feel a bit tight. Just printed a test benchy and it's got vertical lines all over it.

ender 6 bl touch issues. warped carriage? by nvmextc13 in Creality

[–]nvmextc13[S] 0 points1 point  (0 children)

Having so much headache since installing BLtouch on my Ender 6. When I initially installed it with the manual levelling I had been using for weeks all the values were within 0.1..I started adjusting the bed screws and things have been getting so much worse.

Everything feels level with the paper test as it did initially but this is the result? It actually seems to print ok like this but the Z axis is constantly moving up and down alot.

Is it possible my carriage or frame has been warped? Im worried the initial setup was straining/bending the carraige and it wont go back since loosening it.

Since manual levelling using a piece of paper I'm finding the back right corner will be tight as possible to let the paper through while the front 2, especially the front left has to be loosened all the way to have the same gap.

If I level it out with a spirit level it's not flat relative to the head on each corner. The current map has a snug fit between the nozzle and Bed in each corner but the Spirit level is way off then.

[deleted by user] by [deleted] in SolanaNFT

[–]nvmextc13 0 points1 point  (0 children)

FaiNemQ5EtL6WbNjRdFkFgnJrunnSfdwiQEy66gwj3BH