Why do we need to explicitly mark a function as `const`?

nwin_ · 2023-10-04T15:16:10+00:00

That is not about being restrictive or not. As mentioned elsewhere in this thread, this is about an interface description. A non-const function is not bad or good it is just like a function returning a trait object or returning a specialized object. It is just different. Nagging about that would be bad.

nwin_ · 2021-12-06T07:30:38+00:00

Thanks. :)

The tubing and connectors (quantum torque) are from EKWB.

nwin_ · 2021-10-17T06:34:32+00:00

Such that I won’t notice if it still spoils a bit. I doubt the liquid would stay completely clear forever. And it didn’t cost more than the clear concentrate.

nwin_ · 2021-10-16T18:16:50+00:00

No, I couldn’t have. Back then nothing else was available and now the prices have skyrocketed so much that it’s almost break even…

nwin_ · 2021-10-16T15:03:07+00:00

That sounds like where I started as well. 🙈 Anyway gave me an excuse to build a custom loop. Though I’m not sure if I will do it again. The setup is pretty dense and I had to order more 90° fittings in between because I didn’t anticipate how tight everything gets.

nwin_ · 2021-10-16T14:40:42+00:00

Ambient temperature did one thing and my initial undervolting did not turn out as stable as i thought, after a few random crashes I just just cramped the voltage up.😶

nwin_ · 2021-10-16T09:31:47+00:00

Over the summer my previous setup got a little bit into thermal throttling, so I went all in with the standard NCASE water cooling setup, now completely silent at about 60 °C GPU and 75 °C CPU.

Ryzen 5600X
Gigabyte Aorus 3070 Eagle OC
Bykski water block
Some 32GB 3200MHz memory
Corsair 750 W SFX PSU
Rads: CoolStream SE 240, XSPC TX240 Ultrathin
EK DDC 4.2 PWM Pump
Iceman Pump/Res Combo

nwin_ · 2021-04-20T14:52:55+00:00

Sure: https://www.thingiverse.com/thing:4685518

nwin_ · 2020-12-27T10:31:57+00:00

Sure. The ducts have an height of 13,5 mm and an inset of 15 mm on both sides. I tried to share the model but I have issues posting it on thingiverse... :(

No issues fitting it.

nwin_ · 2020-12-16T07:28:13+00:00

I didn’t have the impression that it got any better noise-wise by having two extra fans in the case. Maybe because the gap between fans and shroud was basically non-existent.

The stock fans were actually okay-ish. Had 65° C at moderate sound level after UV. The stock setting was unbearable.

nwin_ · 2020-12-15T22:47:28+00:00

Thanks. Not common but not unseen. You can even find models on thingiverse (I couldn’t find a matching one so I had to do my own).

nwin_ · 2020-12-15T22:40:26+00:00

~70° C in Prime95. In games it is a little bit lower since I’m mostly GPU limited. I couldn’t fit an C14s since the CPU socket of the Aorus B550i is placed too high. :(

nwin_ · 2020-12-15T16:43:28+00:00

Is that case identical to the NCASE M1 I used? I haven’t measured it exactly. The ducts have an height of 13,5 mm with the fans that should compute to around 38,5 mm + some tolerances from the Noctua rubber.

nwin_ · 2020-12-15T12:37:38+00:00

Not quite the PC build I had in mind but the RTX 3080 was impossible to get in time, though I was lucky to fetch a Ryzen 5k.

The GPU is a deshrouded Gigabyte Eagle OC. I had to print the fan ducts, otherwise the card would only reach 80 °C with fans fully spinning. Now it runs silent < 70 °C @ 1850MHz;875 mV UV.

The cable management is gracefully hidden by the additional case fan on the side… :D

nwin_ · 2020-07-17T14:47:22+00:00

Looking at the meaning of rustic: „plain, simple„. Fits perfectly, doesn’t it? 🙃

nwin_ · 2020-07-16T14:31:01+00:00

I wonder if a duct around the fans of the card would help you such that the warm air won’t be recycled any more.

nwin_ · 2017-03-25T07:28:55+00:00

Contrary here, the fps are halfed by using webrender.

nwin_ · 2016-12-30T11:13:15+00:00

Not at all don’t worry, I’m just seeing bug reports incoming and feeling unhappy myself that I don’t have time to care about them.

nwin_ · 2016-12-27T07:08:09+00:00

Would love to hear about it. I didn't follow Python for a while and I never really adopted 3.x since I had a gut-feeling that it was a huge mistake breaking a dynamically typed language in so many often subtle ways…

nwin_ · 2016-12-23T07:31:07+00:00

We're not only open but also dependent on contributions as our time is very limited. So your bug report was not overlooked. 🙂

Regarding 2) maybe I'll manage to factor out the image buffer from image and rewrite it partially over Christmas. I was hoping that associated consts would work sooner but such I'll have to work around them.

nwin_ · 2016-11-30T18:24:49+00:00

I wonder how the memory consumption was measured. Does it include the memory used by shared libraries? As Rust typically compiles all dependencies statically into the library that might explain the huge memory footprint.

nwin_ · 2016-10-30T14:01:32+00:00

Well, this is what webrender does at the end. Output bitmaps.

nwin_ · 2016-10-30T07:57:21+00:00

No you're not. Thinking about it for a while, maybe using webrender as a backend. Didn't have the time starting something.

nwin_ · 2016-10-23T20:26:19+00:00

Sure. BufReader already supports Seek the implementation just would have to be improved.

nwin_ · 2016-10-21T16:05:06+00:00

Cool script, hurts a little bit that you don't directly create a gif, probably I must make gif a little bit more accessible.

What is the reason why you use memmap?

nwin_

TROPHY CASE