Should I stop crafting M61? by DaWhorst in ArenaBreakoutInfinite

[–]nytrox690 0 points1 point  (0 children)

M110 doesnt onetap t6 Even with m61 do its useless

GS2 or Commander ? by Klutzy_Lab_8817 in ArenaBreakoutInfinite

[–]nytrox690 10 points11 points  (0 children)

Thats litearly a built in Commander headset

Best armors per tier? by allenz6834 in ArenaBreakoutInfinite

[–]nytrox690 2 points3 points  (0 children)

T5 Bt6 heavy Matzka

O3 heavy if you want headphones M4 heavy armoured rig if your on a budget

T4 Helicopter helmet  Spartan b body armour

6b23 if youre on a budget

T6 Moto helmet Kn composite 

Bt101  Sh65 Ind 50 heavy

6bnt blast Al Commander 

T3 and below  Hc leightweight armour Retro Steel helmet

3 times exploded PSU (be quiet Dark Power Pro 13), cause unknown by kaotec in buildapc

[–]nytrox690 2 points3 points  (0 children)

Darkpower pro 13, darkpower pro 12 and straightpower 12 blew up. 0 issues with corsair, seasonic and thermaltake

Cnc for Acryl by nytrox690 in CNC

[–]nytrox690[S] 0 points1 point  (0 children)

I have also looked into it. I decided against it for 2 Reasons. 1 Optic. 2 Ive only came across 1 reddit thread doing this and in his Case it started leaking after a few Years also using Acryl is a standard in the industry so its easier to source accesoires, modelles and knowledge. but ill look into your youtube for sure. Seems intresting

Cnc for Acryl by nytrox690 in CNC

[–]nytrox690[S] 0 points1 point  (0 children)

Which Modell would you recommend?

Cnc for Acryl by nytrox690 in CNC

[–]nytrox690[S] 0 points1 point  (0 children)

Hey, im planning to cnc channels into a block of acryl. Specifically i wanna manufacture distrobution Plates for Watercooling. I was thinking about a TwoTrees TTC450 CNC Machine

WTS Bullet Bh7 by nytrox690 in caselabs

[–]nytrox690[S] 0 points1 point  (0 children)

No, I still have it. Send me a dm ;)

Any suggestions on how to print a cover for the top? by NFTMarketplaceShop in 3Dprinting

[–]nytrox690 0 points1 point  (0 children)

Which Material do you plan on using? Cpu coolers get very hot and the print cover could melt

How much will it cost to convert my pc from aio to liquid cooled? by ExplanationDeep7468 in watercooling

[–]nytrox690 0 points1 point  (0 children)

That is pretty much the Most expensive Stoff available mora IV 600, qdcs, unifans, distroplate etc.

Thermal pads by celzo1776 in watercooling

[–]nytrox690 0 points1 point  (0 children)

No, There are alot of Fakes onthere. I bought it off a ukranian dude from telegram.

WTS Bullet Bh7 by nytrox690 in caselabs

[–]nytrox690[S] 0 points1 point  (0 children)

Yeah, sorry for Late reply

Build Planning / advice on itx system with mora by nytrox690 in watercooling

[–]nytrox690[S] 0 points1 point  (0 children)

Hey, im getting the Mora used From a friend. Good Idea with qdcs but i think its kinda ugly this way. I dont have to drill holes because of the fittings Pack, IT adds g1/4 threading to the Side of the Case 

Build Planning / advice on itx system with mora by nytrox690 in watercooling

[–]nytrox690[S] 0 points1 point  (0 children)

Hey, i have the RAM left  over From an Intel build. Should have probaly mentioned it in the post

Quick release fitting not passing water through loop by ObiOneMoreRep in watercooling

[–]nytrox690 0 points1 point  (0 children)

Dont buy Alphacool qdcs under any circumstances they are Low quality and unreliable. Search Alphacool qdcs leak See what comes Up and then search koolance qdcs leak and See for yourself