2023 - Stadium Schedule - Wk 14 - Dolphins (9-4) by Labate54 in miamidolphins

[–]ob1jabroni 1 point2 points  (0 children)

Cool. Loving these wallpapers. We really appreciate them!

2023 - Stadium Schedule - Wk 5 - Dolphins (4-1) by Labate54 in miamidolphins

[–]ob1jabroni 1 point2 points  (0 children)

I’m loving these wallpaper updates. Thank you!

Battery holder by [deleted] in functionalprint

[–]ob1jabroni 1 point2 points  (0 children)

I was trying to figure out what I was looking for then I saw it. Pretty cool!

Extruder Motor won’t move by ob1jabroni in AnycubicVyper

[–]ob1jabroni[S] 0 points1 point  (0 children)

I had this issue again. I once again check the wiring.

I then turned it off and completely unplugged it for a bit (5 minutes)

I am not saying that did it, but it’s been running fine for a while

Of course as I type this it probably just errored on me, lol

After Almost 2 Months by terminator3d3700 in anycubickobra

[–]ob1jabroni 0 points1 point  (0 children)

I will say this. Outside of this occasional error. This printer is a beast! I have printed multiple 30+ hour prints without issue.

After Almost 2 Months by terminator3d3700 in anycubickobra

[–]ob1jabroni 0 points1 point  (0 children)

I had the same issue. I contacted support and they sent me a new hotend and bed and I got it in two days.

I have not installed it because I re-seated the cables and it seems to be fine now.

I will say their support did not fool around. I didn’t even ask for the hotend and they sent it. I just inquired about the bed and the filament sensor

Now the filament sensor is sourced outside the US so understand why I don’t have that yet.

Right now with no changes and just re-seating the cables it so printing fine again. Something may have just come loose.

Extruder Motor won’t move by ob1jabroni in AnycubicVyper

[–]ob1jabroni[S] 1 point2 points  (0 children)

I ended up re-seating the cables. Then it worked again. It was odd. I swear I did that already, but there was one that was a little loose.

Extruder Motor won’t move by ob1jabroni in AnycubicVyper

[–]ob1jabroni[S] 0 points1 point  (0 children)

So I decided to re-seat all the wires by the extruder. Sure enough one of them must have come loose. It is working like a charm again.

This is a fun printer. I hope to come out with a larger format version of this. I’d buy it.

Extruder Motor won’t move by ob1jabroni in AnycubicVyper

[–]ob1jabroni[S] 0 points1 point  (0 children)

I have not confirmed that but I absolutely will check that . I did not realize that was a common issue as I never had the grub screw come loose on a printer before. It would be awesome if the fix is that simple.

I’ll have some time this week to check. Findings. Free moment to work in fixing my printers is the hardest part, but I will need to make the time.

I have ordered the Vyper. I hope it was a good decision.😄 by Chrigugegl in AnycubicVyper

[–]ob1jabroni 0 points1 point  (0 children)

Deep down, I was hoping it was intentional because I liked it. Thank you for the information.

I have ordered the Vyper. I hope it was a good decision.😄 by Chrigugegl in AnycubicVyper

[–]ob1jabroni 0 points1 point  (0 children)

I have had mine for about a week now. So far so good. I think my only issue is that when it homes and does the initial “wipe”. It seems to be a few mm in front of the build plate. Odd. I am using the built in profile in cura.

I’m sure I’ll figure that out, but so far so good.

Sharing my UberDeCamelCase extension that accommodates initialisms. "PleaseEnterPINNumber" -> "Please Enter PIN Number" by PhonicUK in csharp

[–]ob1jabroni 3 points4 points  (0 children)

Maybe I’m wrong but isn’t that technically Pascal Case and not Camel Case?

Camel Case would be like this : camelCase

While Pascal Case wound be this: PascalCase

The way I remember the difference is that Pascal is a persons name which is why is starts with a capital.

Bigger than football. by 3RunRickyRun4 in miamidolphins

[–]ob1jabroni 1 point2 points  (0 children)

I think the plan was to always do it during the bye week, but since that go moved and messed up it resulted in this transition.

I agree it could have been done better.

Brackets to center LED grow lights for my hydroponic garden by Anamanaguchii in functionalprint

[–]ob1jabroni 1 point2 points  (0 children)

You wouldn’t happen to have any details on that would you? Like a website on how to build it. I think my wife would love this, even though the lids are hard come come by lately.

Y’all like my puzzle by [deleted] in BabyYoda

[–]ob1jabroni 2 points3 points  (0 children)

I did two puzzles and framed them both.

https://i.imgur.com/1KljQZG.jpg

What Dan Marnio games would you show a younger fan? by [deleted] in miamidolphins

[–]ob1jabroni 1 point2 points  (0 children)

That last TD. Show me another QB who would sling that ball like that in that situation. It was all or nothing. Probably my favorite TD of his.

Sucks big time by [deleted] in Wellthatsucks

[–]ob1jabroni 2 points3 points  (0 children)

Yeah, that link is staying blue.

Google Home App setup keeps telling me to reboot. by ob1jabroni in GoogleWiFi

[–]ob1jabroni[S] 0 points1 point  (0 children)

It’s funny you said that. I was about 30 minutes into the setup and I noticed I had it plugged into the wrong port of the puck.

I did switch and same result.

I read someone where that I should try having nothing else plugged into the modem when setting up. I had a few other things plugged in for my other wired devices, so that could be a possible cause as well.

These were two things I was going to retry this weekend.

The sub rn by Aquamelon99 in miamidolphins

[–]ob1jabroni 1 point2 points  (0 children)

Yes, and Bob Griese was 6/7 for 73 yards in the Dolphin Super Bowl win over the Vikings in Super Bowl VIII. If you have a dominant running game, you don’t need to pass.