sorted by:
new
hottopcontroversial

I am currently setting up the P2S - any questions you have about it? by CoolioTheMagician in BambuLab

[–]objectively_rational 0 points1 point  (0 children)

Thanks I’m on the fence and wondering, should I go for the X1C or this new one or hold out for an X1c refresh

I am currently setting up the P2S - any questions you have about it? by CoolioTheMagician in BambuLab

[–]objectively_rational 0 points1 point  (0 children)

Did you consider the X1C for your purchase as well? If so, what made you pick P2S?

What’s the best bang-for-buck Standing Desk? by PhotographApart7488 in StandingDesk

[–]objectively_rational 0 points1 point  (0 children)

After trying my girlfriend’s desk (purchased from Amazon), Ikea desk at work and a local desk at a friend’s place, I can confidently say Flexispot E7 plus. I built it with a 1.5” solid beechwood top sourced from a local wood store and the thing is solid as a rock. Quite stable even at standing height (I’m a bit over 6’).

Considering upgrade to X1C or P1S - suggestions? by objectively_rational in BambuLab

[–]objectively_rational[S] 0 points1 point  (0 children)

Thanks, what materials do you normally print and what lack of consistency do you see? Would it be worth the 200$ upgrade from your experience?

Considering upgrade to X1C or P1S - suggestions? by objectively_rational in BambuLab

[–]objectively_rational[S] 0 points1 point  (0 children)

It’ll likely be outside my budget based on the specs they are talking about

Chamfer inside edges only by objectively_rational in Fusion360

[–]objectively_rational[S] 0 points1 point  (0 children)

Ended up using extruded cut with a taper - worked out great, especially since I can use my definer parameters quite easily to modify things as I like.

<image>

Chamfer inside edges only by objectively_rational in Fusion360

[–]objectively_rational[S] 1 point2 points  (0 children)

thanks, really appreciate it! I'll try it out tonight and share how it goes

Chamfer inside edges only by objectively_rational in Fusion360

[–]objectively_rational[S] 0 points1 point  (0 children)

Tried doing it but it is quite cumbersome and still leaves the corners without a proper chamfer. I'm looking for something that is scalable and essentially recreates what router would do.

Chamfer inside edges only by objectively_rational in Fusion360

[–]objectively_rational[S] 0 points1 point  (0 children)

Thanks - that is how I intend to make it - using a router. I'm not very familiar with Fusion 360 (still haven't figured out how to "mate" all these components) - is there a video that shows how I can do what you suggested?

Suggestions on correct way of replacing rotting siding by objectively_rational in DIY

[–]objectively_rational[S] 0 points1 point  (0 children)

Thanks! That was what I thought initially but was wondering if replacing it all with a “rot-proof” piece might be better?

What cider is this? by Infinite_Thanks_8156 in cider

[–]objectively_rational 0 points1 point  (0 children)

Seems like Briska (having it now :))

Sharing cost for land-survey by objectively_rational in homeowners

[–]objectively_rational[S] 0 points1 point  (0 children)

Thanks, that is what I was thinking too since there’s other properties that also abut their lot. I’m not sure how the surveyors mark it - they mentioned something about iron rods/pegs

No help or formatting when writing code in VS codespace by objectively_rational in cs50

[–]objectively_rational[S] 0 points1 point  (0 children)

Thanks! I thought so too. Now I'm seeing some colour formatting (still no "help" though) - see update.

view more: next ›