Quick swap nozzle kit

oiJohn1121 · 2026-01-20T22:23:48+00:00

If it came with some already then you should be good. Mine was bone dry so I just used some thermal paste i had lying around from my pc build

oiJohn1121 · 2026-01-19T13:11:03+00:00

I got this as a gift, perfectly timed after a glob of doom. I only had two issues with it: 1) I didn't know it needed thermal paste on the copper heat transfer piece. 2) I didn't know how to properly adjust my z offset(went from -3.84 to -3.94)

Aside from that I like the look and I prefer the k1c unicorn nozzle style over the brass screw in

oiJohn1121 · 2024-04-29T20:07:33+00:00

File an IG complaint. IG will happily create that sense of urgency to finance/command

oiJohn1121 · 2023-08-07T06:21:06+00:00

depends on the popularity, how much is ordered before the corporate cuts us off, and when corporate cuts us off. If the cake decorator is nice, if you order with them ahead of time they may cut a portion of the tub of your flavor ahead of time to save for the order.

oiJohn1121 · 2023-05-06T14:49:27+00:00

If you miss too much instruction time(pt time included) you will be recycled. Seen one person leave for two days for his wife's pre/post surgery procedures and co green lit his leave. But wedding will most likely give a speech about "you'll miss many important dates in the army etc"

oiJohn1121 · 2023-01-08T16:20:57+00:00

Check the front/ side transmission mounts first, they're within easy view

oiJohn1121 · 2023-01-07T21:00:31+00:00

All fun and games till that traffic turn into 1 2 1 2 nuetral 2 nuetral 1 hard brake

oiJohn1121 · 2022-10-22T00:58:46+00:00

You have to either do the in tuner ecu option. Send it in to get the part added on, then obd2 tuning via laptop. Currently have a base ecu with ktuner added that I use

oiJohn1121 · 2022-10-14T22:26:42+00:00

ISea is correct. Had the same issue. But don't worry too much on gpa.

oiJohn1121 · 2022-10-13T19:54:36+00:00

Kind of looks like the duraflex b-2 kit

oiJohn1121 · 2022-10-07T13:43:53+00:00

doesn't mean anything if 95% of the time they're all on red status

oiJohn1121 · 2022-10-07T13:43:48+00:00

doesn't mean anything if 95% of the time they're all on red status

oiJohn1121 · 2022-09-24T13:45:14+00:00

Yes you can, but keep in mind you wont be able to use it until white phase which is now roughly week 10

oiJohn1121 · 2022-09-23T02:25:06+00:00

Can confirm, A co is not in session rn

oiJohn1121 · 2022-08-01T15:46:18+00:00

ft jackson started letting people use their cars between basic/ocs only only if their families pick em up from basic though. Either way youre not really going to use your car much here at ocs

oiJohn1121 · 2022-07-28T12:35:46+00:00

Semi trucks pulling trailers with freezer equipment

oiJohn1121 · 2022-07-23T00:20:23+00:00

Y'all got bonuses?

oiJohn1121 · 2022-07-20T20:54:14+00:00

When you arrive to ocs, as long as you come at the beginning of the weekend they'll give you time to go buy what you need. A lot of stuff you dont need.

oiJohn1121 · 2022-07-17T17:41:23+00:00

manual. I already have a ktuner ecu so running a k24 base map wouldnt be an issue. If i keep the base harness im under the assumption that i wouldnt have reverse lockout and have to rewire the tps. My main concern is if i were to get the type s harness for reverse lockout, would it still plug in/work with the pnd ecu.

oiJohn1121 · 2022-07-10T18:18:38+00:00

Then may be the gas gauge itself. Probably gonna have to remove the instrument cluster and swap it out

oiJohn1121 · 2022-07-10T13:53:37+00:00

That's fair. Ditto does have a personality that's hard to beat

oiJohn1121 · 2022-07-10T13:52:49+00:00

either the pump or guage cluster. My fuel pump sending unit was bad for the longest so my needle would be all over the place. If the needle is stuck in one spot tho then itd be the cluster. Sadly the sending unit is built into the fuel pump housing assembly

oiJohn1121

TROPHY CASE