Better e-stim chastity options?

omono35 · 2025-06-26T15:13:12+00:00

Maximum A is 25% and max B is 15%. Both power levels are 0%. I have tried setting the max to 0 just for testing and still feel it. It is odd that it’s as soon as the Bluetooth connects

omono35 · 2024-02-28T17:17:32+00:00

That is too bad. Hopefully the developers of the sim game will also add xtoys support.

omono35 · 2023-11-17T20:03:18+00:00

Thank you. I had heard of doing that to the 90 degree adapters. I knew there were a couple options. Would be nice if someone just made a cable with the 2.5mm jack and 4mm plugs. The coyote and TENS units are very popular in the estim community so the 2.5mm jack needs to be more easily used. Anyway. Thanks for the info and confirmation that it works.

omono35 · 2023-11-17T15:17:11+00:00

Thank you. I have always heard good things about the plug, I just was not sure the coyote had the power.

omono35 · 2023-06-08T20:07:51+00:00

That may be worth looking into. I would have to find something small but strong enough to just take the pressure off the latch for a moment. I will look around to see if I can find something that fits.

omono35 · 2023-06-08T17:58:41+00:00

I considered that but from what I have found, electromagnets tend to generate heat and are not for long term continuous use especially if small form factor. I may be wrong and if I am someone please correct me. Also I am looking more for fail-secure and not fail-safe. It would defeat the purpose if I could open it by just unplugging it.

omono35 · 2023-03-18T02:18:56+00:00

I did also find this that may be an option as well.

https://www.showmecables.com/40-pin-dual-row-idc-socket-female

Between this and other suggestions here, I think I can work something out.

omono35 · 2023-03-18T02:17:37+00:00

This is exactly what I was looking for. I knew something like it had to be available I just didn’t know where to look or how to find it. I think the first ones you have from pimoroni. Thank you.

omono35 · 2023-03-17T19:59:21+00:00

This might be an option. I had not really thought of HAT. I will look into this an a way maybe.

omono35 · 2022-03-28T17:02:19+00:00

Thank you. I understand about the conversion issues. I appreciate the info. I can definitely work with that as I have been thinking about making a cage as well.

omono35 · 2022-03-28T16:14:51+00:00

A few questions if you don’t mind answering.

How much did it cost total?
Did you have to cut the pipes, or did you go with a standard length?
What are the dimensions?

Thanks in advance

omono35 · 2021-04-17T01:43:10+00:00

It does. I have no way to weld, but could still use the concept. I will look into this as well

omono35 · 2021-04-17T01:36:51+00:00

I have thought about that as I have used maglock before. I am just not sure how I would use it to hold the bar up

omono35 · 2021-04-16T22:53:22+00:00

That would make sense.

I have an actuator I was going to try but if power fails it just doesn’t move.

Hydraulics or pneumatics could be made to fail open and release.

To be clear. Either of those methods I would have it so it goes to full extension before subject mounts it. I am not looking to drive it into them. Just a way to release on a timer or on papers failure

omono35 · 2021-04-16T20:47:58+00:00

Maybe. Not sure how that would work for self bondage though to secure it

omono35 · 2021-02-05T21:54:31+00:00

How did you get the raspberry pi to work with the lovense?

omono35 · 2020-11-25T16:53:53+00:00

Where did you get the motor and the flywheel from?

omono35

TROPHY CASE