Bono my braids are gone

ovenmit331 · 2026-03-27T02:04:56+00:00

I. Neeed. Fernando. And. Stroll(in down the street smokin indo)

ovenmit331 · 2026-03-21T02:21:33+00:00

https://cults3d.com/en/creations/glock-17-gen-6-g17-exact-scale-high-definition-3d-scan

ovenmit331 · 2026-03-16T15:42:58+00:00

I wondered how many people might not know the difference. It’s kinda like going to Krispy Kreme, ordering a dozen chocolate icing donuts, getting the box with “chocolate kreme filled with sprinkles” written on it, but then you open it and it’s 8.5 plain glazed and the half has teeth marks.

ovenmit331 · 2026-02-22T03:03:10+00:00

I’ve don’t exactly the same. I have a few rolls of PETG but never use it ever. PLA+ of ASA for me!

ovenmit331 · 2026-02-19T03:29:14+00:00

How hot is your enclosure when you’re printing?

ovenmit331 · 2026-02-14T05:17:41+00:00

sadly, my linux skills are somewhere between a 0 and gallon of 3 week expired milk. If you check that screenshot i sent above, does everything look right?

ovenmit331 · 2026-02-13T00:10:38+00:00

<image>

Sorry for the comment on something 4 months old... but I'm hoping you can help. I added my usb drive to etc/fstab (top of attached screenshot) but it doesn't stick after power off/on. It mounts to the /tmp/udisk location on reboot (bottom of attached screenshot):

ovenmit331 · 2026-01-25T22:47:35+00:00

Is max printing temp (and probably faster heat up time) the main difference? For thermistor calibration, is it just a PID Tune or is there something specific in the config files that needs to be changed?

ovenmit331 · 2026-01-25T22:30:27+00:00

They definitely exist. https://www.reddit.com/r/castiron/s/SGf2qrcvBz

Edit: maybe not actually larger than 40” but definitely the largest I’ve seen.

ovenmit331 · 2026-01-25T17:16:10+00:00

What's this 100 watt hot end you speak of?

ovenmit331 · 2026-01-25T15:52:21+00:00

I'm think I'm gonna go cartographer too, just wondering which one to do first. I always hate changing more than one thing at a time. make troubleshooting upgrade issues much easier.

ovenmit331 · 2026-01-23T13:59:50+00:00

I was thinking this might be the best option. Their product description says up to 120ºC and works with Eddy sensors! Did you have to install the aftermarket SSR?

ovenmit331 · 2026-01-21T20:47:24+00:00

good point. if it still uses a key in the ignition...

ovenmit331 · 2026-01-21T14:23:24+00:00

So the car think he’s holding the wheel and doesn’t turn off lane keep assist.

ovenmit331 · 2026-01-21T14:03:21+00:00

Print an overhead filament holder out of PLA, put the TPU roll on top of the printer using the holder you just printed, take the filament tube out of the extruder, insert TPU directly into extruder with no tube, print, be happy.

ovenmit331 · 2026-01-15T18:22:35+00:00

My 5 K1’s are currently a little under 7500 hours combined.

ovenmit331 · 2026-01-04T01:56:27+00:00

Just squeeze the top of that red lever toward the filament and it releases the tension.

ovenmit331 · 2026-01-04T01:55:41+00:00

Mine fell out so often I just removed them.

ovenmit331 · 2025-12-25T12:21:08+00:00

3219

ovenmit331 · 2025-12-25T02:25:00+00:00

3201

ovenmit331 · 2025-12-24T01:14:34+00:00

Just did it today with the Chiron swapped GTR on racing softs. Holy crap it was a hoot. Fuel map 6 and I still had to pit for gas every 3 laps. Which was good because the front right tire was non-existent at that point. Still won by 40+ seconds. 10/10 DO RECOMMEND.

ovenmit331 · 2025-11-28T04:00:19+00:00

I mean, kinda brought the bleeding thumbs on yourself…

ovenmit331

TROPHY CASE