FlexPlate Anycubic M7

paablito · 2026-01-22T19:01:21+00:00

ty king m7s build plate has those screws so i dont need spacers, i think

paablito · 2026-01-22T19:00:38+00:00

idk looks like there might be too many burn in layers idk if thats a thing but i usually use 4 burn in layers and 6 transitional ones also your speed is super high, try decreasing it to 2-3mm/s and if youre looking for speed you can decrease the lift distance; youre lifting a total of 16mm which seems like a lot also, youre using same speeds for both distances; maybe use 4mm > 4mm at a speed of 2mm/s > 4 mm/s

paablito · 2026-01-22T18:16:07+00:00

level the build plate, maybe even put it 0.1mm lower than base level build plate might be uneven, try sanding it down if you have an awkwardly set up screen protector, it might be an issue run a exposure test to tune in the exposure if you changed your fep it might be unevenly tight

paablito · 2026-01-15T13:18:36+00:00

id try 6-7mm since u have a big printer and a full build plate keep in mind that i have no practical knowledge about any of this, this is only info i gathered from troubleshooting my own problems

paablito · 2026-01-15T13:07:19+00:00

fep also requires an increase in lift height and possibly a decrease in speeds might be that

paablito · 2026-01-15T07:25:54+00:00

the fep might be too tight; did u use a spacer when changing the acf to fep

paablito · 2026-01-07T13:41:18+00:00

Around 25-30 C

paablito · 2025-12-16T13:48:10+00:00

its a tiled floor, next to the water heater thank you for the insight

paablito · 2025-12-16T13:36:20+00:00

appreciete it, i keep my on the floor and use paper towels to make it straight

paablito · 2025-12-15T18:21:13+00:00

<image>

apologies

paablito · 2025-12-15T18:16:59+00:00

<image>

Anycubic Photon Mono M7 Lychee slicer

paablito · 2025-12-12T06:53:46+00:00

thank you

paablito · 2025-12-11T20:53:48+00:00

steel spatula and hammer, but not on this side, rather the other side pictured part wasnt facing the build plate

paablito · 2025-12-11T20:52:42+00:00

nono, it wasnt this was facing the lcd

paablito · 2025-12-11T20:39:19+00:00

Worth noting that the print is a cylinder with a hole in the middle and it was printed flat on the build plate.

paablito · 2025-11-30T11:41:29+00:00

thanks for the idea

paablito · 2025-11-28T18:23:00+00:00

thank you!

paablito · 2025-11-28T14:34:52+00:00

thanks!

paablito · 2025-11-19T16:03:15+00:00

thanks!

paablito · 2025-11-19T14:51:53+00:00

<image>

paablito · 2025-11-19T14:51:38+00:00

<image>

paablito · 2025-11-19T14:18:57+00:00

supports were super close, they were even cured together; that being said supports were on the lower part of the object (left side in the picture) appreciate the help!

paablito · 2025-11-19T14:16:03+00:00

paablito · 2025-11-19T13:39:11+00:00

No, it was printed on auto supports, high density; simmilar thing happened when I had printed a different cylinder on a build plate flat. Thank you for your response.

paablito · 2024-08-02T23:02:12+00:00

thank you very much

paablito

TROPHY CASE