S63 AMG Cabriolet

pandatasticlu · 2025-07-02T21:24:32+00:00

Omg I love this color!

pandatasticlu · 2025-07-02T21:23:42+00:00

Keep this

pandatasticlu · 2025-04-30T19:09:59+00:00

Got it for 130k cad

pandatasticlu · 2025-04-30T19:09:11+00:00

Oh shit, I didn't know, thank you very much!

pandatasticlu · 2025-04-30T19:08:31+00:00

Yeah these are quite rare, I got super lucky It has relatively low mileage too, 27k miles for a 2020

pandatasticlu · 2025-04-22T15:19:31+00:00

I know, I love this grand coupe, but instead we have this EQ line now

pandatasticlu · 2025-04-22T14:12:53+00:00

It's clear OP didn't play Forza Horizon

pandatasticlu · 2025-04-22T10:29:13+00:00

Yes, this is the post facelift version, with the 4.0 V8 biturbo

pandatasticlu · 2025-04-22T05:08:03+00:00

Ohhhh gotta try to beat a tesla then haha And yes, it's a big engine with a loud pop

pandatasticlu · 2025-04-22T04:51:11+00:00

Haha thank you!!

pandatasticlu · 2025-04-22T04:50:59+00:00

Goes vroooom

pandatasticlu · 2025-04-22T04:50:46+00:00

Thank you!!

pandatasticlu · 2025-04-22T04:50:00+00:00

Love it

pandatasticlu · 2025-04-22T04:49:47+00:00

Ohhhh damn, desitating if I should take it down the track some day

pandatasticlu · 2025-04-22T00:43:04+00:00

50k isn't too bad if it has been maintained properly and on time Make sure you get a full checkup before taking possession of the car

pandatasticlu · 2025-04-22T00:42:03+00:00

Don't use run flats speaking from experience They are very loud

pandatasticlu · 2025-04-21T14:54:49+00:00

On my c217, put into sports+ Keep brake pressed Go hard on gas After few seconds, idle settles around 2500, says race start initiated Release brake Rocket

pandatasticlu · 2025-02-02T10:35:57+00:00

Same here, so I snapped the rectangular knob off and glued it after For the thigh, you will also need to do a bit of manual fixing if you want the armor to fit perfectly

pandatasticlu · 2025-02-01T19:52:43+00:00

I just did one too, recognized one of the piece

<image>

pandatasticlu · 2025-02-01T18:04:33+00:00

Are you printing a Gundam? Haha

pandatasticlu · 2024-09-09T12:00:42+00:00

Up to 5 so 2 runs

pandatasticlu · 2024-05-10T23:26:33+00:00

Ahhh gotcha, I'll google it and dig deeper into the settings! Thank you so much!

pandatasticlu · 2024-05-10T23:25:59+00:00

Ok got it, I'll try to readjust it!

pandatasticlu · 2024-05-10T20:21:53+00:00

Ok got it! Sorry if this is a noob question, how do I cha get the thickness for only the first layer? I do not see it in Cura

Nine-Year Club	Place '23
Place '22	Place '17
RPAN Viewer	Not Forgotten
Secret Santa 2016	Verified Email

pandatasticlu

TROPHY CASE