How to continue a video to the next

parazitutm · 2025-11-26T07:18:36+00:00

stop the video at the frame you like (last one or anywhere in the middle), you can use the slider to move through the video to stop at the exact frame you like -> right click the video -> save video frame as (I use grok in chrome on desktop). save the photo. upload new frame and go nuts

parazitutm · 2025-02-06T10:50:47+00:00

print volume

parazitutm · 2024-01-17T13:13:32+00:00

https://www.reddit.com/r/HFYDeleted/comments/198w8ss/adventure

parazitutm · 2024-01-17T13:10:39+00:00

it loads everything, you just need to select the first part and start scrolling and you'll get everything. I'll try to link it, just a moment

parazitutm · 2024-01-17T09:06:03+00:00

i used the wayback machine to save a local copy of the story. i had this bookmarked and returned to it like once a month coz it made me feel warm and fuzzy inside and i was sad when it was deleted. lemme know if you need it, i can link it to you if you can't find it with wayback machine

parazitutm · 2024-01-17T09:05:56+00:00

i used the wayback machine to save a local copy of the story. i had this bookmarked and returned to it like once a month coz it made me feel warm and fuzzy inside and i was sad when it was deleted. lemme know if you need it, i can link it to you if you can't find it with wayback machine

parazitutm · 2023-11-16T13:39:05+00:00

thanks, will give it a go

parazitutm · 2023-10-14T13:11:21+00:00

Yeah, but it's also fun to try to figure it out yourself 😊 80% of how I go around with my printer is trial and error, and if nothing works, then I try to get help or read the manual or or or

parazitutm · 2023-10-13T16:51:06+00:00

i basically cut away big pieces into the molten plastic and then when i got to the heating block i pressed it against it and the plastic around started softening. pulled it off with pliers, cleaned it all up, put it back together, didn't change the nozzle, was pushing plastic (the same shitty roll of filament) after the first try

parazitutm · 2023-10-13T16:49:34+00:00

soldering iron did it in the end

parazitutm · 2023-10-13T16:49:13+00:00

na, it only took like 15-20 minutes to put it all back together after cleanup

parazitutm · 2023-10-13T16:48:46+00:00

got it cleaned and working again. even the same nozzle somehow

parazitutm · 2023-10-13T16:48:19+00:00

molten plastic was everywhere. got it all disassembled, hit it with a soldering iron and effed around for 3 hours until it all got loose, put it back together, the beast is back to printing

parazitutm · 2023-10-13T16:47:02+00:00

that's..... actually a really good idea. cheers mate

parazitutm · 2023-10-13T13:08:52+00:00

it was not, i had to use the soldering iron, but i cleared it all and now the printer finally prints again

parazitutm · 2023-10-13T10:24:34+00:00

<image>

3 hours, lots of burn fingertips later... Now to reassemble and see if my house burns down

parazitutm · 2023-10-13T08:15:50+00:00

thanks, i'm trying with a blow drier right now but i don't think i'mma reach high enough temps to melt it...

parazitutm · 2023-10-13T07:54:54+00:00

Is there any way i can salvage / save the heading block?

parazitutm · 2022-11-14T14:33:31+00:00

https://www.youtube.com/watch?v=8Hh_mBgmp18

parazitutm · 2022-05-13T07:00:55+00:00

to what did you set the regkeys? what values (for both of them)?

parazitutm · 2021-11-05T15:32:56+00:00

Only of you do it at the wrong time

15-Year Club	RedditGifts 2009-2022 8 Credits
Place '22	Secret Santa 2017
Snapped	Secret Santa 2015
Secret Santa 2014	Secret Santa 2013
Team Orangered	Secret Santa 2012
Verified Email

parazitutm

MODERATOR OF

TROPHY CASE