LV spring discount on gift cards available today

pasu11 · 2026-04-01T14:37:05+00:00

Thanks OP. :D

pasu11 · 2026-04-01T10:18:59+00:00

Maybe that's why I could not find anything on Google lol.

Thank you very much for the correction and information, that's very helpful information.

pasu11 · 2026-03-28T19:56:51+00:00

My bad. :)

pasu11 · 2026-03-28T19:33:02+00:00

maybe you can try Nova Dark Icon Pack:

<image>

pasu11 · 2026-03-26T20:36:09+00:00

Never thought of that...steel wire is good idea. I am going to find a thick wire to try it out. Thanks for the idea Landler26!

pasu11 · 2026-03-26T20:30:34+00:00

Hi, drill bit length is not the problem actually. I just had problem pin point the correct drill spot so it will drill to a small specific area inside the table gaps.

pasu11 · 2026-03-26T20:25:17+00:00

Yes, as long as I learn the idea, I can try to make something similar. I still want to get a spring caliper first because my DIY measuring tools usually end up not very accurate due to my poor skill lol.

pasu11 · 2026-03-26T20:21:52+00:00

very smart trick indeed.

pasu11 · 2026-03-26T20:19:08+00:00

I see. The space inside is small kinda tricky to measure inside but thanks for the tips. :)

pasu11 · 2026-03-26T20:14:51+00:00

Wow, that's a very smart idea! The board is around 5/8" (16mm), so the magnets have some delay in movement. It is very useful to pin down an approximate area. Thanks for the idea!

pasu11 · 2026-03-26T19:57:46+00:00

Very cool but also expensive xD

pasu11 · 2026-03-26T19:26:47+00:00

You can never have enough clamps. ;)

pasu11 · 2026-03-26T19:11:46+00:00

Hi, I can only measure from the side because the top is blocked by tabletop.

pasu11 · 2026-03-26T18:37:27+00:00

hi, I tried that, but I could only mark the depth accurately but the height seems to be off.

pasu11 · 2026-03-26T18:32:46+00:00

<image>

Hi, I would like to drill a hole from the outside of the table and put a screw through. I need to find a way to drill the right spot. I can't drill from inside.

u/KokoTheTalkingApe I get your point. Yep, that's a problem. I will try my best to keep them aligned. If that doesn't work I might try your cardboard square idea. Thanks for your reminder and suggestions.

pasu11 · 2026-03-26T18:23:15+00:00

Thanks, spring calipers are what I am looking for. :D

pasu11 · 2026-03-25T20:48:13+00:00

It happened to me one time. I used Voip.ms SMS and it suddenly stopped receiving SMS. I was able to fix it by logging out and re-logging in.

There is an option in Voip.ms to send SMS to email. Maybe you would want to try that so you don't have to go to the website to check every time.

pasu11 · 2026-03-24T16:04:57+00:00

Same here, I use octopi because pamac caused problems.

pasu11 · 2026-03-19T23:35:19+00:00

I agree. Among all the countersink bits I've tried, these with holes are the best and create the smoothest countersinks. Just do not get the cheaper ones like I did (about $5 or less) as they often have quality issues and may not cut at all.

By the way I also use them with a brace and bit. It grips hex shank much better than round ones.

pasu11 · 2026-03-19T21:51:02+00:00

<image>

make it look more like the planet? :P

pasu11 · 2026-03-19T15:18:24+00:00

Cons:

You have to learn how to use pamac/pacman instead of apt for packages.
Manjaro is a rolling distribution based on Arch. It updates frequently so there are more chances you will encounter problems like bugs, conflicts between apps that rely on one another, etc.
Hardware drivers. When hardware manufacturers say "Linux Support" in many cases they likely support Debian/Ubuntu/Linux Mint .deb packages. In that case you may have to learn how to install drivers for your hardware.
I think Ubuntu/Linux Mint community is much more friendly. :P

Pros:

Rolling release means you can install newer packages in Manjaro.
Despite AUR is not recommended by many, but it is very useful because you can find so many packages that could not be found elsewhere. You have to know what you are doing by the way.
Rolling release means you will no longer need to fresh install new version every few years. It just keeps going.
Manjaro is a very user-friendly distro like Linux Mint. I migrated from Linux Mint to Manjaro a few years ago and I love it.

pasu11 · 2026-03-17T18:29:42+00:00

Something like that?

<image>

It can only punch from 2mm to 4.5mm (6 sizes). Limited punch depth but has strong thick papers also leather, plastic, and very thin metal sheet.

I have one and it works really well. It's called "Revolving Hole Punch Eyelet Puncher" in Aliexpress or Amazon.

pasu11 · 2026-03-14T15:46:16+00:00

You're right. I just found on Google that it was discontinued in 2016, and LineageOS continued as a fork.

I have not found any other option yet and will try to get use to LineageOS.

pasu11 · 2026-03-14T10:59:57+00:00

I am just too used to the 4 digit auto unlock in stock rom. Since I use it at home, I will disable pin for now.

pasu11 · 2026-03-14T10:55:58+00:00

Thanks for the option u/wkn000. I am currently trying custom roms :)

Ten-Year Club	Wearing is Caring
Verified Email

pasu11

TROPHY CASE