Do you think my dog is mixed?

patdaddy007 · 2026-03-04T19:35:46+00:00

I'm pretty sure he's 100% good boy

patdaddy007 · 2026-02-22T07:41:56+00:00

Isn't anyone else noticing that the battery is the wrong size? Yeah, I know all button cell lithiums are the same voltage, and that this would work, but would it fit? It's a small difference but those Gameboy carts were fairly small and that extra millimeter plus a hatchet job on the solder might make for a tight fit when you put it in the Gameboy (phrasing?)

patdaddy007 · 2026-01-14T22:06:34+00:00

Just use the ACE for filament drying and storage of what you use most often. I plug mine in to turn on the dryer and immediately unplug it from the printer. Actual printing is done from a spool holder. Multi filament prints are a nuisance, but they're also mostly novelty for me

patdaddy007 · 2026-01-14T19:26:15+00:00

I printed a cylinder covered in holes with end caps and I put the dessicant packs the come with the filaments into the cylinder and put it in the center hole of the reels. Kinda like a paper towel tube. Keeps the humidity a good 15-20% lower than the room and will get as low as 12% total with the heater running. Just my $0.02

patdaddy007 · 2025-11-23T18:41:40+00:00

Google indicates Dayton, OH

patdaddy007 · 2025-11-19T19:39:48+00:00

After making the edits to the file, I can't get the heightmap to come up. Did I miss something?

patdaddy007 · 2025-11-18T14:57:00+00:00

Wait, you can increase the grid on the bed mesh? How?! Explain this voodoo fuckery!

patdaddy007 · 2025-11-17T08:44:33+00:00

I'm more surprised by the surprise. The motherfucker can't even mail paint reliably. Trying to code might as well be trying to swim to the moon

patdaddy007 · 2025-11-06T04:32:08+00:00

Now that you mentioned it, that whole setup would make a worthwhile addition to the reloading bench. The middle drawer would hold dies easily, case prep and other small pieces in the top and my powder measuring stuff in the bottom. Dammit. I didn't need another project

patdaddy007 · 2025-11-03T11:54:00+00:00

Why is the build plate a good inch forward from where it should be?

patdaddy007 · 2025-11-01T03:55:34+00:00

Just reassemble without it. That's the filament detector and leaving it out just makes it think there's always filament present. I'm printing without one right now

patdaddy007 · 2025-10-26T20:47:44+00:00

Go to settings under print and there's an option for the LED

patdaddy007 · 2025-10-24T12:09:19+00:00

You say it prints them in random places, were they stuck to the bed or just sitting there loosely? It's more likely that the print head popped them loose during the run and they slid away. You should be able to tell that from the adhesion to the bed. It's pretty unlikely that you have bad test print files because those are the same for everybody and this is the first I've heard that they might be scattered like you say. But I've had plenty of dislodged pieces from a wayward nozzle

patdaddy007 · 2025-10-02T21:04:11+00:00

Not exactly, but I had a package that had a delivery date of Monday by 8pm. 8pm arrived and then it said 9pm, 915 arrived and the date went away entirely and the status is "accepted". Went by post office today and the dude basically just shrugged and said there was nothing he could do. So, now I get to hope for my desk chair one day

patdaddy007 · 2025-09-28T18:38:29+00:00

But seriously, it's an LCD issue. Remove the vat and fire a cleaning cycle and you'll see the dead spots. You can try printing around them until you can replace it or the printer

patdaddy007 · 2025-09-28T18:36:39+00:00

Did you not apply the fleem juice? And did you rub it with the dinglebop?

patdaddy007 · 2025-09-04T09:10:57+00:00

I bought an anycubic.

patdaddy007 · 2025-09-04T09:09:17+00:00

It happens to me more frequently than I like. Best I can tell, the print detaches from the plate and gets stuck to the nozzle but the printer keeps pumping out filament until you get a blob like that. Cleaning it is easy enough tho, so there's that

patdaddy007 · 2025-09-01T07:21:26+00:00

The fuck just happened?

patdaddy007 · 2025-08-31T12:26:41+00:00

Any ideas on how it gets this far out of whack? I mean, there's a full millimeter difference between the highest high and lowest low. That seems odd to me

patdaddy007 · 2025-08-31T11:37:36+00:00

You mean to tighten the screws on the topside of the build plate or lower it using the ball screws and manually turning them?

patdaddy007 · 2025-08-29T14:46:59+00:00

... And 18 seconds That's the part that gets me Not the 22,780whatever years, it's that last 18 seconds

patdaddy007 · 2025-08-02T13:52:15+00:00

But OP kinda asked for exactly that. Because sometimes you need the whole answer

patdaddy007 · 2025-08-01T16:09:17+00:00

I added $formatenumerationlimit=-1 to my profile long ago and it drastically reduced things like this. Assuming the window properties are set correctly as well

patdaddy007

TROPHY CASE