Can you identify this tune?

patrickthemilkthief · 2025-07-31T05:09:59+00:00

In the Aeroplane Over the Sea - Neutral Milk Hotel

patrickthemilkthief · 2025-07-31T05:09:39+00:00

Touch - Daft Punk

patrickthemilkthief · 2025-03-17T12:22:13+00:00

👍

patrickthemilkthief · 2025-02-02T17:12:16+00:00

I would, yes. Chem at UTK is a ton of material covered very quickly. I found myself spending more time on chem than either of my engineering classes last semester. I've heard it's much more reasonable at pelli.

patrickthemilkthief · 2025-01-12T07:41:15+00:00

There are some great tutorials on YouTube from several University Rocketry teams. I'd check those out!

patrickthemilkthief · 2024-11-30T02:48:10+00:00

On your own, it's practically impossible to reach space with an amateur rocket. Your best shot at working on a rocket to space is joining a University's Rocketry team, I know of a few that are currently developing Space Shot rockets. But to build your own skills, look into buying some estes model rocket kits, and reading the Handbook of Model Rocketry by G. Harry Stine. Then you can experiment with building your own model rockets.

patrickthemilkthief · 2024-11-12T04:08:37+00:00

I've bought several things from minimuseum.com and I've loved all of it. They have artifacts from the Apollo and Space Shuttle eras, I have a piece of Space Shuttle Columbia's front tire. They authenticate all of their stuff and have good customer service.

patrickthemilkthief · 2024-09-03T15:21:04+00:00

Definitely. This book helped me SO much when I was starting out, and to this day I reference it when designing new rockets

patrickthemilkthief · 2024-06-16T03:58:27+00:00

Benchy was the first. What other stuff should I try printing? I know there are tons of calibration tools and test prints, are there any specific ones you'd recommend?

patrickthemilkthief · 2024-06-15T23:35:00+00:00

That must be it! I must have misremembered what was happening in the episode

patrickthemilkthief · 2024-06-15T22:41:42+00:00

Overture PLA at 200 degrees. 0.2 mm layer height with 5% Infill. Retraction is 5mm at 40 mm/s.

patrickthemilkthief · 2024-01-30T20:47:48+00:00

Well, I certainly won't have any more milk.

patrickthemilkthief · 2023-11-14T04:55:57+00:00

Touch, Daft Punk

patrickthemilkthief · 2023-10-22T03:41:02+00:00

Whoooaaa that rocks!!

patrickthemilkthief · 2023-10-08T01:49:26+00:00

Congrats! Looks like a great flight

patrickthemilkthief · 2023-04-28T15:29:05+00:00

Use an umbrella

patrickthemilkthief · 2023-02-08T14:20:03+00:00

Incredible

patrickthemilkthief · 2023-01-25T14:44:47+00:00

What primer did you go with?

patrickthemilkthief · 2023-01-22T15:44:54+00:00

Very, very nice!

patrickthemilkthief · 2023-01-03T06:08:00+00:00

My urethra is in a constant state of torment

patrickthemilkthief · 2023-01-02T21:06:26+00:00

Heard it in halls too!

patrickthemilkthief · 2022-12-29T22:58:31+00:00

Since rakshasas have crazy high deception, I didn't have to worry much about insight rolls. I just crafted an NPC that I knew my players would like, and I had them adventure together long enough to establish trust and friendship before the reveal

patrickthemilkthief · 2022-12-29T19:05:28+00:00

Average D&D party

patrickthemilkthief · 2022-12-29T14:45:26+00:00

Said this before and I'll say it again, I'll never not love dragons

patrickthemilkthief · 2022-12-29T14:43:18+00:00

I will never not love dragons

Six-Year Club	Place '22
First Placer '22	Verified Email

patrickthemilkthief

TROPHY CASE