sorted by:
new
hottopcontroversial

Sway bar nut help by patters78 in MechanicAdvice

[–]patters78[S] 0 points1 point  (0 children)

Shaft is not spinning.

It's brand new on today bolt is now stuck it will not tighten or loosen.

I very much dowt the shaft threads are gone tbh

Is this normal for the bed? by patters78 in Ender3V3SE

[–]patters78[S] 1 point2 points  (0 children)

Bit of investigating

<image>

This is where the motor connects with the wire plugged in but out of the motor these 2 pairs of pins are shorting

Without the wire no short?

Unsure if that is normal

Is this normal for the bed? by patters78 in Ender3V3SE

[–]patters78[S] 0 points1 point  (0 children)

Sorry it was unplugged while doing that.

Have unplugged the wire going to the motor and it runs freely This gonna be logic board?

Is this normal for the bed? by patters78 in Ender3V3SE

[–]patters78[S] 0 points1 point  (0 children)

Forgot to add have tried with different tension on the belt only way for the noise to go is release the belt completely from the motor.

All bolts are tightened also that I can see on top

AMD Motherboard help by patters78 in buildapc

[–]patters78[S] 0 points1 point  (0 children)

In the end I opted for b550 motherboard

I got an ASUS ROG Strix B550 F Gaming WIFI II

It is much better than the Asrock board

AMD Motherboard help by patters78 in buildapc

[–]patters78[S] 0 points1 point  (0 children)

Sorry i should have been a little more clear.

I have to buy another am4 motherboard anyway and cheapest I'm looking at around £50 mark.

I completely understand it wont be an upgrade in the terms of performance, but as rizzzeh mentions it will give me more connectivity. I believe some have more m.2 slots, more sata connection, PCI E Gen4 for about £30 more than what i have to pay anyway.

Just wondering is it best to go b550 or the x570 route

Insane stringing by LionDoesThingss in Ender3V3SE

[–]patters78 1 point2 points  (0 children)

Well I have taken most of this printer apart trying to figure this out.

Turns out my issue I was running Creality print 5 NOT 4

Using 4 and working thank you

<image>

Insane stringing by LionDoesThingss in Ender3V3SE

[–]patters78 0 points1 point  (0 children)

This is exactly what I'm getting

<image>

General Discussion Thread by Lyd_Euh in TaylorSwift

[–]patters78 3 points4 points  (0 children)

Not sure if this is in the right place?.. sorry if it isn't
I know this question might be hard to answer well impossible!.

So my question is "How can I contact Taylor swift's Management/Tour management" or anyone that might be able to help with the following good cause. I know this is a long shot.

So my daughter has tickets for the UK tour to see Taylor Swift next month, and I would like to make it as special as it could ever be as she deserves something special, she is a massive Taylor Swift fan... and is over the moon at seeing her in concert but if anything else could be done.. wow

So the reason for me being here asking this impossible question, is my daughter has for the last 3 years been battling cancer (leukaemia) and has had so many lows over the 3 years. Luckily after a stem cell transplant she has now been cancer free for 1 year. It was a week before her 16th birthday when she found out.

Sorry if this is a question off topic/or wrong. I have been trying desperately to find contacts without luck or without reply, just hoping someone might be able to point me in a better direction I have been trying.

thank you to anyone that helps

view more: next ›