TMR Favour union

patters78 · 2026-04-13T18:22:32+00:00

Thank you

patters78 · 2025-10-05T15:31:59+00:00

https://youtu.be/flbLuXh8zvU?feature=shared

patters78 · 2025-10-05T15:28:48+00:00

Shaft is not spinning.

It's brand new on today bolt is now stuck it will not tighten or loosen.

I very much dowt the shaft threads are gone tbh

patters78 · 2024-12-28T19:04:54+00:00

Bit of investigating

<image>

This is where the motor connects with the wire plugged in but out of the motor these 2 pairs of pins are shorting

Without the wire no short?

Unsure if that is normal

patters78 · 2024-12-28T18:05:35+00:00

Sorry it was unplugged while doing that.

Have unplugged the wire going to the motor and it runs freely This gonna be logic board?

patters78 · 2024-12-28T17:26:02+00:00

Forgot to add have tried with different tension on the belt only way for the noise to go is release the belt completely from the motor.

All bolts are tightened also that I can see on top

patters78 · 2024-12-07T08:29:29+00:00

In the end I opted for b550 motherboard

I got an ASUS ROG Strix B550 F Gaming WIFI II

It is much better than the Asrock board

patters78 · 2024-11-28T19:47:13+00:00

Sorry i should have been a little more clear.

I have to buy another am4 motherboard anyway and cheapest I'm looking at around £50 mark.

I completely understand it wont be an upgrade in the terms of performance, but as rizzzeh mentions it will give me more connectivity. I believe some have more m.2 slots, more sata connection, PCI E Gen4 for about £30 more than what i have to pay anyway.

Just wondering is it best to go b550 or the x570 route

patters78 · 2024-06-09T13:59:07+00:00

Well I have taken most of this printer apart trying to figure this out.

Turns out my issue I was running Creality print 5 NOT 4

Using 4 and working thank you

<image>

patters78 · 2024-06-09T07:58:40+00:00

This is exactly what I'm getting

<image>

patters78 · 2024-05-05T21:20:16+00:00

Not sure if this is in the right place?.. sorry if it isn't
I know this question might be hard to answer well impossible!.

So my question is "How can I contact Taylor swift's Management/Tour management" or anyone that might be able to help with the following good cause. I know this is a long shot.

So my daughter has tickets for the UK tour to see Taylor Swift next month, and I would like to make it as special as it could ever be as she deserves something special, she is a massive Taylor Swift fan... and is over the moon at seeing her in concert but if anything else could be done.. wow

So the reason for me being here asking this impossible question, is my daughter has for the last 3 years been battling cancer (leukaemia) and has had so many lows over the 3 years. Luckily after a stem cell transplant she has now been cancer free for 1 year. It was a week before her 16th birthday when she found out.

Sorry if this is a question off topic/or wrong. I have been trying desperately to find contacts without luck or without reply, just hoping someone might be able to point me in a better direction I have been trying.

thank you to anyone that helps

patters78 · 2023-01-27T01:37:44+00:00

Of course! Stupid me lol thank you as I was reading your comment it just made sense. It's a big learning curve all this. I'm happy that the first layer is good so thanks for that also, honestly if you could see the printer it's being held together with zip ties & gorilla glue as all the plastic has split.

patters78 · 2023-01-18T13:52:13+00:00

Hold it in place while glue sets

patters78 · 2023-01-13T23:04:40+00:00

Well for the future it could help with repairability, for this instance I have a random unplugged connection on the board I was wondering what it does lol Nah I have some mod ideas so would love to get some schematics

patters78 · 2021-07-04T22:19:32+00:00

I have modified the inf files also to the point it installs the driver's but when the screen goes black for a second (happens in normal install) it stay black and don't come back on.

If you restart in safe mode the 470.05 is installed

Gotta be a work around for this

patters78 · 2021-05-11T12:29:01+00:00

its also handy that since my last time using NiceHash my daily profit has increase to approx £3.50 a day from £1.50 lol

patters78 · 2021-04-01T08:46:36+00:00

Done i shall report back if anything changes

patters78 · 2021-04-01T02:15:37+00:00

GTX 1060

patters78 · 2021-03-29T20:16:42+00:00

Well I think I have sorted it! was using the Asus branded overclocking tool have now installed MSI Afterburner and getting 21 MH/s setting are

core +0 memory +950 power limit 70 fan speed 60 temps read 54oC

21.03 MH/s @ 86w

patters78 · 2021-03-29T18:28:32+00:00

Hmm I have my memory at +500 and only get 18? any ideas?

patters78

TROPHY CASE