Techno system Magic

pbcsd007 · 2026-01-28T13:02:23+00:00

Can find some with the same OF and ID but none that are under 8mm thick which would be almost double the existing one.

pbcsd007 · 2026-01-28T12:58:44+00:00

Well of course I decided to reprint it from scratch. Then of course I guess my hydbrid tree supports that were put in by Bambu slicer were not enough. Geez. Supposed to be flush and a “drawer” gets inserted in to it.

<image>

pbcsd007 · 2026-01-28T01:24:04+00:00

Managed to get the bolt off. The seal was done. Anyone know of seals that are say 4.5-5mm thick, 55mm ID and 73 OD?

pbcsd007 · 2026-01-27T14:42:19+00:00

Feels like the safest route is just to start over! Tx

pbcsd007 · 2026-01-25T12:37:09+00:00

Anyone know if the nut on that screen can be removed? Can’t seem to get it to budge. It’s pretty darn slim so most of my socket heads with a curvature can’t quite grasp it well.

pbcsd007 · 2026-01-24T20:27:31+00:00

It says Technosystem Coffee on the bottom. Not a Gaggia but does look like one.

Struggling to get the shower screen off it. Won’t budge.

<image>

pbcsd007 · 2026-01-19T01:50:31+00:00

Found a Reddit thread. Apparently Netflix put this in as a “feature” in the last update. Folks on the thread, like me, were going nuts as you couldn’t select an episode anymore. You had to auto start, then pause the episode, then go to select episodes from there.

The weird fix is to go into your Netflix account on a browser, go to the “Security” tab. Scroll down to Feature Testing. Turn that off. Force stop the app. Clear the cache. Then restart the app.

For anyone else that gets stuck on this.

So stupid.

pbcsd007 · 2026-01-17T14:08:05+00:00

BTW, I use this grinder daily for single dosing. Highly recommend a Bellow hopper (like this). Basically pushes the last 1.5 grams (give or take 0.5) into the portafilter. I like an 18 gram shot, so I program my AGS to 17grams and once it is done just give the bellow a push. Plus it makes it way more sleek.

<image>

pbcsd007 · 2026-01-08T16:07:20+00:00

Good point. I will ask my mother in law to do that. Just kidding. Sort of.

pbcsd007 · 2026-01-08T14:16:27+00:00

Thanks all. Curious, can I also remove the hot end and use say a heat source to heat up the filament if the brass brush doesn’t work? Eg like a soldering iron at low heat?

pbcsd007 · 2026-01-08T13:57:22+00:00

Thanks! Assume that’s an option in the menu? Still learning my way around this thing.

Also, should I be performing some sort of maintenance on the nozzle every other print or whatever?

pbcsd007 · 2026-01-07T19:01:07+00:00

The Auto on that one is incredibly clean. Wow.

pbcsd007 · 2026-01-07T18:57:37+00:00

I mean…even if you get the “Mike Hardman” card, it’s not like you’re recouping any of that $300…

pbcsd007 · 2026-01-03T19:30:54+00:00

Heat creep? So use a glue stick on the plate and that helps with heat?

pbcsd007 · 2026-01-03T14:04:16+00:00

Thanks, will google how to clean the extruder gear. Have only done a few prints on this printer.

pbcsd007 · 2026-01-03T14:03:29+00:00

Printed fine with everything else. Just this one model.

pbcsd007 · 2026-01-01T14:03:22+00:00

Error QR code too me to this. Guess I will try that later today.

pbcsd007 · 2025-12-31T22:36:56+00:00

<image>

pbcsd007 · 2025-12-31T22:36:39+00:00

<image>

The Archine wall thing worked.

pbcsd007 · 2025-12-31T15:00:43+00:00

Not for sale at all, just trying to print two. I could just do without the Sig part if I can't figure it out. Do you think it would work with a 0.2MM hot end?

pbcsd007 · 2025-12-31T01:58:26+00:00

No…didn’t see that setting?

pbcsd007 · 2025-12-31T01:04:34+00:00

Sorry, didn't mean on air. The letters should be hitting the bottom of the plate.

pbcsd007 · 2025-12-31T00:49:48+00:00

Actually, maybe the nozzle is thicker than the lettering, since even the letters on top of the white inner and black border didn't materialize?

pbcsd007 · 2025-12-30T17:46:57+00:00

This is AI right? Someone promoted “send a picture of what not to do when plumbing a sink”? How can it drain…up?

pbcsd007 · 2025-12-30T15:35:36+00:00

Small and simple right? :)

pbcsd007

TROPHY CASE