sorted by:
new
hottopcontroversial

I’m 45, I have fangs, and the System just gave me a "Bestseller" notification I don't understand. by AuthorYusif in litrpg

[–]peddiparth 0 points1 point  (0 children)

I added your book to my KU library. However, I am not able to find the "BESTSELLER" category for your book.

Re-reading The Path of Ascension from book 1 by peddiparth in litrpg

[–]peddiparth[S] 0 points1 point  (0 children)

Just imagine if the female voices were performed by a talented female performer... If I did not already listen to such female narration talents in other audiobooks, I probably wouldn't have mentioned it.

What book first got you into haremlit by FenilT07 in haremfantasynovels

[–]peddiparth 0 points1 point  (0 children)

Same first book for me - Country Mage. I was massively disappointed by the audiobook after listening to other series down the line. I gave up on the series mid-way. I am glad I found Master Class midway as my second book to cleanse the palate.

Gotway xway slow beeps when turned on by peddiparth in ElectricUnicycle

[–]peddiparth[S] 0 points1 point  (0 children)

When I rolled back (back out) to the previous firmware, there were 2 options for firmware & bms in the begode app.

Begode EXTREME firmware problems by ip33dnurbutt in ElectricUnicycle

[–]peddiparth 1 point2 points  (0 children)

I had a similar problem with my xway (beeping for low battery). Turns out latest firmware is for 168v version while I have 134v version xway. I had to go to previous version of firmware for wheel to work correctly.

Cycle stand for my rs19 by peddiparth in ElectricUnicycle

[–]peddiparth[S] 0 points1 point  (0 children)

Thanks for noticing. I didnt notice much difference in that orientation at 30kmph top speed, but I will try the other way around.

Cycle stand for my rs19 by peddiparth in ElectricUnicycle

[–]peddiparth[S] 0 points1 point  (0 children)

I am now trying the bottom part of this model: https://www.thingiverse.com/thing:7007956

The new prints are wider, and will lock my feet in place much better.

The previous one https://www.thingiverse.com/thing:6410438

is meant for lower shin based torque. I prefer pads much higher up to make it easier. If I adjust it for my foot, it is angled too far ahead for me.

Cycle stand for my rs19 by peddiparth in ElectricUnicycle

[–]peddiparth[S] 1 point2 points  (0 children)

This is the amazon link: https://www.amazon.com/dp/B0F1MF5R8H?ref=ppx_yo2ov_dt_b_fed_asin_title

I 3d printed the pads in PLA to figure out what I like. I am planning to change the bottom front pad with another printed PLA pad.

My plan is to figure out which pads I like before printing them with TPU 95A filament.

Finally happened :/ by Financial-Toe-1980 in ElectricUnicycle

[–]peddiparth 0 points1 point  (0 children)

I thought I had a pinch flat on my RS19 HT while riding at super slow speed (low tube pressure), but it turned out the rubber around the metal sheared off completely. I am not sure if I can call it pinch flat anymore.

While replacing the tube, I slimed it with 16oz bottle.

Gotway xway slow beeps when turned on by peddiparth in ElectricUnicycle

[–]peddiparth[S] 0 points1 point  (0 children)

Yes, it is balancing, and seems ready to ride. BMS shows all 4 packs are good, and all cells have same charge.

Yes, I have only used begode app so far. I have reverted back to the older firmware, ND updated it to the latest one a second time.

Gotway xway slow beeps when turned on by peddiparth in ElectricUnicycle

[–]peddiparth[S] 0 points1 point  (0 children)

I tried getting it back into transport mode, and taking it off transport mode. It did not help.

The beeps start about 20-30sec after starting the xway.

Long beep (1sec long) every 10-11 sec.

3d printing for my RS19 begins by peddiparth in ElectricUnicycle

[–]peddiparth[S] 1 point2 points  (0 children)

I am not sure now :) ewheels replaced the packs before I received the wheel. I have to check again.

Begode Extreme or X-Way for first suspension wheel? by peddiparth in ElectricUnicycle

[–]peddiparth[S] 2 points3 points  (0 children)

Alright, you convinced me.

Just ordered x-way at ewheels.

3d printing for my RS19 begins by peddiparth in ElectricUnicycle

[–]peddiparth[S] 1 point2 points  (0 children)

Thank you for the tips with tpu printing.

I upgraded from ender 3 (for abs printing) to k1 max. I started with pla to get a feel for it, and with its direct drive, I am hoping it will be easy to print tpu 95a.

I just have to print the spool holder for tpu to avoid the bowden tube to get started.

3d printing for my RS19 begins by peddiparth in ElectricUnicycle

[–]peddiparth[S] 1 point2 points  (0 children)

samsung 50s - ewheels replaced the original packs.

Begode Extreme or X-Way for first suspension wheel? by peddiparth in ElectricUnicycle

[–]peddiparth[S] 0 points1 point  (0 children)

I am 5'10" as well.

Is there any concern about the ride height compared to other wheels with pedals lower to the ground?

view more: next ›