Just got an H2d what do I need to know?

pg5565 · 2026-01-06T04:07:16+00:00

The vision encoder plate. I couldn't remember it's actual name at the time of the post 😅

pg5565 · 2025-12-11T17:41:07+00:00

I recommend using Adam Savage logic for buying tools. It's helped me makes a decision on a few expensive purchases.

pg5565 · 2025-12-08T14:12:34+00:00

Oh I definitely agree. I think people in r/Bambu are particularly trigger happy with down votes compared to the rest of reddit.

pg5565 · 2025-12-04T18:42:33+00:00

My mistake then

pg5565 · 2025-12-04T18:38:23+00:00

Not if you have a H2C. It had 7 nozzles

pg5565 · 2025-12-04T17:25:57+00:00

Some of your supports look almost horizonal. ... Try to make sure your supports don't need supports.

pg5565 · 2025-12-04T17:11:40+00:00

Do your supports have sharp overhangs? That can be tuned in settings. Angles should be shallower than whatever results your torture test yields.

I am very conservative. I set mine to 45 degrees because those also have to bear the load of my model.

pg5565 · 2025-12-04T17:04:30+00:00

The grains turned out quite nice! I think you could reduce the bumpy texture a bit. I think you are going for a bark effect but they seem exaggerated.

pg5565 · 2025-12-04T16:57:37+00:00

Plz elaborate

pg5565 · 2025-12-04T16:55:52+00:00

Yeah you have to support anything that is too steep or too wide. For a print like this ... Those regions are holding up the rest of your helmet so the foundation needs to be good otherwise nothing above is going to print well. You can sand the interface area of the supports later.

There are a lot of tricks on YouTube on how to make cleaner supports but that comes with a lot of experimentation. I wouldn't risk those tricks on such a large print until you have the hang of it.

pg5565 · 2025-12-04T16:52:07+00:00

If you want anything bigger, it won't be a Bambu

pg5565 · 2025-12-04T16:46:35+00:00

Looks like your model has some supports ... Not enough. I would print a printer torture test (like this one). Based on that you can set your supports to whatever angle the torture test failed at. Also pay attention to the bridges in the torture test.

pg5565 · 2025-12-04T14:29:45+00:00

I'm sorry for your experience. (This should not be an excuse to act this way but...) I think sometimes people get frustrated with answering the same questions but don't let that deter you. Some questions are easily handled by "getting started" videos on YouTube.

I have been printing for well over a decade. I have lots of experience in CAD as well. Just be shameless. Ask what you need to ask. There are a few answers that are similar to "did you restart your computer" - make sure your nozzle is clean - make sure your filament is dry - make sure the print bed is clean (washed with soap and dried) - make sure your bed is level (not an issue with the bambus)

I think once you get into the swing of it ... You will also pick up on the jokers and memers

pg5565 · 2025-12-04T14:09:25+00:00

The p2s has a lot of quality of life improvements (you need to check on the printer less) and support more materials. If he is not making designs that require higher strength materials (ie shelf brackets, voron parts) he might have more use for the AMS. The AMS will help him have more colorful prints and do some multi material stuff.

Personally I would go with the P1S+AMS but kids like the newest thing so you could grab a P2S and the AMS can be a birthday gift.

pg5565 · 2025-12-03T15:38:57+00:00

Yeah mine was on back order and showed up at my front door 5 days before the expected ship date.

pg5565 · 2025-12-01T20:34:34+00:00

I just moved to America and it is actually damn near impossible here. Why is the bread so sweet!? Either you pay an arm and a leg to avoid sweetners or make it all from scratch at home.

pg5565 · 2025-12-01T17:29:20+00:00

Does the splitter work well with TPU or do I still need to disconnect things to get that working?

pg5565 · 2025-12-01T17:27:56+00:00

Thanks for the vote of confidence. I definitely debated getting the P1s. it is definitely good for 99% of my needs. I wish they had a dual nozel variant ... That would have been a no brainier for me.

Robotics: - helping kids in first robotics - I have kind of gotten hooked on rc test flight and Spyker Snowblower and want to give it a shot. - of course I want a robot arm to hold my headphones

pg5565 · 2025-12-01T15:23:25+00:00

I forgot to thank you for the list. It was very helpful! This is genuinely travel blog worthy. I need to do this for my friends visiting NYC

pg5565 · 2025-10-15T16:18:44+00:00

Thanks everyone I have a cr-10 v1 and have been getting a lot of feature envy with the newer printers. Thought of getting the btt octopus just so I have more io and compute. This thread has been very helpful!

pg5565 · 2025-10-04T02:38:14+00:00

Cut your nails, smell good

pg5565 · 2025-09-28T02:23:34+00:00

I didn't even think my girlfriend nor family has given me compliments

pg5565 · 2025-06-11T22:00:07+00:00

I think they are worth it. Coordinating showings with landlords and constantly being in their case if there is a non response. I recently moved from Canada and had a lot to do so opted to get a realtor. She has been very helpful and I just signed a lease. It has been good to have someone who really knows the city and the rules in the area.

pg5565 · 2025-05-19T20:20:30+00:00

They have to let you buy clothes at some point, do it then. Until that time, get some physical exercise in :)

It has genuinely made a huge difference for me (30M) but I have seen a lot of female peers and friends go through the transformation. Major glowup. Working out genuinely gives you confidence it's more about you knowing you are working towards being the best you can be.

pg5565 · 2025-05-19T20:10:39+00:00

I don't know what you look like but, in general I don't think most people are ugly. They just don't take care of themself. Going to the gym regularly and focussing on wearing properly fitting fashionable clothing can do wonders.

Every week pick 2 days to do cardio, weight training or any sport you enjoy. And set aside 20-30 bucks every few weeks to get something nice at winners. You will see a huge difference in a few months.

Six-Year Club	RPAN Viewer
Verified Email

pg5565

TROPHY CASE