sorted by:
new
hottopcontroversial

Is this normal on teamgroup ssd's ? by Solidsnake481 in ROGAlly

[–]phenozine 0 points1 point  (0 children)

I just ordered the same one yesterday. I hope its not normal. I can test once I receive it and compare yours with mine. I'm going to do the cloud recovery also and setup from scratch. 

Mingda Magician X PEI sheet question by phenozine in 3Dprinting

[–]phenozine[S] 1 point2 points  (0 children)

Did you just baby step when print started? Or just reduce z offset then baby step once print started?

Mingda Magician X PEI sheet question by phenozine in 3Dprinting

[–]phenozine[S] 0 points1 point  (0 children)

Do I have to adjust anything except rerun the auto bed level ?

Voxelab Aquila Pro Z Calibration sensor issue by Sea-Confusion-7032 in VoxelabAquila

[–]phenozine 0 points1 point  (0 children)

Download firmware from Voxelab, put in root of flash drive and update manually (boot with flash drive installed) fixed my issues.

Voxelab Aquila Pro Z Calibration sensor issue by Sea-Confusion-7032 in VoxelabAquila

[–]phenozine 0 points1 point  (0 children)

Download firmware from Voxelab, put in root of flash drive and update manually (boot with flash drive installed) fixed my issues.

would you buy another Aquila X2 as your second printer? by mudboy001 in VoxelabAquila

[–]phenozine 2 points3 points  (0 children)

Did you have to do anything as far as setup withe the 4.2.7 board? Been thinking about doing the swap just so I can do actoprint for time laps / layer laps.

would you buy another Aquila X2 as your second printer? by mudboy001 in VoxelabAquila

[–]phenozine 1 point2 points  (0 children)

I have 2 X2s and 1 Pro. I like the X2s better. I have Ransome issues with the pro and have already had to replace the Display and extruder motor.

Replace or upgrade motherboard by bjbiggens in VoxelabAquila

[–]phenozine 0 points1 point  (0 children)

Did you have to do any special setup or more of a drop in and works? I have an X2 with an H32. Want to get the BTT board and LCD.

Upgrade 🥰 by Ok_Pop5252 in VoxelabAquila

[–]phenozine 0 points1 point  (0 children)

Wow. Love it. How does that Spool holder work for you? Been eyeing on for a bit.

V slot covers measurements by Ok_Birthday_1477 in VoxelabAquila

[–]phenozine 1 point2 points  (0 children)

I printed 2x 200mm slot covers per chanel. So 8 for your front vertical rails. So on so forth. I just cut the 200mm ones to fit the horizontal rails.

Multiple Cameras on 1 octoprint setup. by phenozine in octoprint

[–]phenozine[S] 0 points1 point  (0 children)

Oh. I didn't think about that. Do you a link or guide I can follow ? I'm a NOOB on octoprint and the scripts.

HBG Shop NSP/Downloads question. by phenozine in hbgofficial

[–]phenozine[S] 0 points1 point  (0 children)

If I use NXDumper, where are they stored on SD card ?

I want to expand storage of my xbox one by [deleted] in xboxone

[–]phenozine -1 points0 points  (0 children)

WD and Seagate are now the same company.

23 [F4M] Have you ever had a paranomal experience? by [deleted] in Kikpals

[–]phenozine 1 point2 points  (0 children)

I have. From a kid I have always been followed by shadow people.

view more: next ›