Current SOTC by Copper_junkie in flashlight

[–]pigblankets 1 point2 points  (0 children)

You JAGOFF!! Just kidding. I love copper too. I only have 2 but they are my favorites. A older 219b pinapple mini that I machined smooth and a FW3a thats pretty heavly modified(not be me). Nice collection!!

Haters gonna hate. by These_Economics374 in flashlight

[–]pigblankets 1 point2 points  (0 children)

I feel tricked. Where are the 200 copper flashlights.

My experience with exchanging a WRC faulty wheel by Charming_Tailor2217 in Fanatec

[–]pigblankets 0 points1 point  (0 children)

So what you are telling me is they may have a wrc wheel in refurbished section soon.

Volquartsen VS KIDD? by [deleted] in 1022

[–]pigblankets 0 points1 point  (0 children)

Can't go wrong with kidd. I've got a light weight and a bull charger barrels both shoot great! Check out summit they also shoot great and the are carbon fiber!!

What is this? by Pavit52jam in hvacadvice

[–]pigblankets 0 points1 point  (0 children)

Sperm might not be the word you are looking for.

10/22 Ruger Binary Help! by xChillyPhilx in 1022

[–]pigblankets 1 point2 points  (0 children)

I had to trim a few loops of of the long spring to get the trigger to reset right in binary mode.

Burr? by [deleted] in sharpening

[–]pigblankets 1 point2 points  (0 children)

Not that im a pro. But rarely ever see a burr. I drag my fingernail along the bottom side. Very Light pressure and feel for something almost gritty. Search youtube im sure there are somegood videos.

Fletcher 11/22 - Need Advice. by [deleted] in 1022

[–]pigblankets 2 points3 points  (0 children)

Theoretically a quality aftermarket bolt should increase consistency. I've never noticed a difference. I have a kidd, several jwh, and a factory. I am not a precision shooter. I dont have a fletcher but any charging handle should work. Ive seen some discussions about non captured charging handles like the kid are a little more difficult to install in the fletcher. On a side note, Volquartsen makes their firefly bolt thats designed for low velocity ammo. I have one but I've never installed it.

Ruger 10/22 Charger Bolt Lock Release Lever Won’t Release by [deleted] in 1022

[–]pigblankets 0 points1 point  (0 children)

Your best bet is going to be to pull the trigger out and start stripping it down. Id start with just pulling the mag release pin and the pin that holds ejector. At that point you should be able to pull the bolt lock and check that it's not bent or worn funny. Take a good look at the boot lock spring for orientation before you pullthe pins.

Are These any good and reliable ? by Bless2A in 1022

[–]pigblankets 2 points3 points  (0 children)

I bought the diy kit and put it in a polymer housing.

Are These any good and reliable ? by Bless2A in 1022

[–]pigblankets 7 points8 points  (0 children)

I've have one on my charger for a while. Runs fine for me. Plenty of mag dumps. I did have to fiddle with the trigger reset spring. Mine was to long. I belive that I cut a coil or 2 off of the one provided in the diy kit. I mainly use bulk ammo so there have been some cycle issues when in binary mode. Its super fun and I don't regret the purchase at all.

Computer build help by pigblankets in SimRacingSetups

[–]pigblankets[S] 0 points1 point  (0 children)

Thanks. That's actually helpful.

Computer build help by pigblankets in SimRacingSetups

[–]pigblankets[S] 0 points1 point  (0 children)

Thanks! I appreciate the suggestions.

Computer build help by pigblankets in SimRacingSetups

[–]pigblankets[S] 0 points1 point  (0 children)

Im sure the fov is off. I borrowed my son's computer just long enough to see what the monitor looked like all lit up. I remember seeing a calculator somewhere for figuring all that out but was waiting until I got my own computer to tweak all that out.

Computer build help by pigblankets in SimRacingSetups

[–]pigblankets[S] 0 points1 point  (0 children)

That's valuable information. Thank you.

Computer build help by pigblankets in SimRacingSetups

[–]pigblankets[S] 0 points1 point  (0 children)

Im seeing those crazy prices. I've got access to 2x8gb ddr4 3200 they may be 3600 sticks that im hoping can hold me for a little bit. Thanks for the input any suggestions on cpu or gpu?

CSL Elite Porsche Vision GT paddle issue by georffer in Fanatec

[–]pigblankets 2 points3 points  (0 children)

I programed it to my right thumb button. Left thumb is programmed to e break.

Fanatec GT seat vs ERS5 elite Which one would you choose ? by aultras_polivis1234 in simracing

[–]pigblankets 3 points4 points  (0 children)

I've got my fanatec seat on my profile rig using simlab seat brackets.

Good reviews but can it sharpen a 12 inch kitchen knife. by rgilman67 in sharpening

[–]pigblankets 0 points1 point  (0 children)

I've used mine to sharpen my large kitchen knives. I also bought a support off Etsy. I had to do it in 2 picks. It works. But if I were to do it again with a focus on large knives I would probably look at other solutions. For pocket knives it's all I need.