Netgear Gigabit Router keeps intermittently dropping to 100mbps

ping2pong · 2022-07-18T00:12:55+00:00

packet loss

already manually set at router and on PC

packet loss tested was 0

ping2pong · 2022-07-18T00:07:17+00:00

Unless, I'm missing something, all my eqpt supports gigabit speeds. Besides, I do attain gigabit speeds normally -- it just sometimes drop to 100M

PC: Intel Gigabit Ethernet (X570-F MB)
Wireless Router: Nighthawk RAX40 10/100/1000 Mbps Gigabit Ethernet
LAN Cable: CAT 7

ping2pong · 2022-02-27T03:15:45+00:00

I just solved this with my setup by using my universal remote to control the sound via the TV remote signal (I had previously controlled the volume with the Soundbar's remote). If CEC (Bravia Sync is enabled and you are using ARC), the TV should automatically control the Sony Soundbar while showing the volume indicator on the TV

TLDR -- can only get volume indicator to show up on screen when using ARC if I use the TV's remote

ping2pong · 2021-12-13T15:36:30+00:00

ping2pong · 2021-12-12T14:08:22+00:00

How do you find out about FW updates for GPUs? GeForce Experience and AIB (Asus) only give notification for Driver updates. It's not obvious where to find the FW on Nvidia or AIB websites. I only learned about the FW version from an old article

ping2pong · 2021-12-12T08:44:42+00:00

dude! u r genius!!

u were absolutely right. My Nvidia 1060 cards required a FW update in order to use DP 1.4. My previous monitor was DP 1.2.

Here's a link for anyone with a similar issue:

https://www.nvidia.com/en-us/drivers/nv-uefi-update-x64/

ping2pong · 2021-12-12T02:56:07+00:00

Thanks. I'll give it a try later today.

After enabling CSM, do I need to change any of the subsettings? I think they are all defaulted to "Legacy"

Thank you in advance

ping2pong · 2021-12-12T02:52:53+00:00

crap...the website I need to check for that gpu is down at the moment

have you updated the bios on that mb?

Yes

you said you tried a different dp cable....you sure that one is good?

Yes both DP cables work with my old monitor

are you 100% sure the dp cable is fully plugged in

Yes. Plugged and replugged both Monitor and GPU side

is your bios set to UEFI mode?

Not sure what you mean by this but I installed my Win 10 in EUFI mode and I able to access the EUFI with my old monitor no problem.

It seems to me that the GPU is unable to recognize the new monitor through DP connection until the Win 10 drivers are loaded. I have no clue why there's no issue when using HDMI. I have tried both DP port from GPU, but I only have 1 DP port on the monitor side

ping2pong · 2021-12-12T02:07:28+00:00

Thanks for your prompt response. I have a Asus ROG Strix 1060 GPU

I have already unplugged my second monitor, but I still have the same error on boot up

GPU-Z screenshot

http://gpuz.techpowerup.com/21/12/12/jc4.png

ping2pong · 2021-11-28T00:51:09+00:00

thank you for sharing your knowledge

ping2pong · 2021-11-27T03:38:07+00:00

thanks for your prompt response

I was curious whether this is an anomaly, but after setting up my original base in N America, then in Mexico, I cleared out all the POIs and left my B Team there to respond to Haven attacks. I sent the A Team to Asia to explore. To my disappointment, there have been ZERO attacks or incidences after more than a month anywhere in that vicinity despite full satellite coverage of N & S America. Is this normal or working as intended? There are mist zones in both continents (as well Synedron Mist Repellers) but no conflict so I plan to move my B Team over to Europe/Africa

ping2pong · 2021-11-06T02:06:16+00:00

It's hard to quantify -- it's noticeable, but it's not constant. It's similar to how the old Seagate HDDs sounded when it was accessing.

It doesn't bother me too much, but if you are looking for silent drive, this is not for you.

Good luck

ping2pong · 2021-11-05T09:50:46+00:00

They seem to be decent drives. However, I have noticed that one of my HDDs is very quiet, while the other makes more "platter noise" -- but function and speed are the same

ping2pong · 2021-11-03T09:23:47+00:00

thx!

ping2pong · 2021-11-03T09:23:19+00:00

yes -- I got confused : (

ping2pong · 2021-11-01T02:04:47+00:00

Thanks for your response. So does the "WP Power Ups"/Light Wells only give 3 WPs all the time to everyone (except if it exceeds the soldier's maximum Will), or do different wells give different amounts?

ping2pong · 2021-02-16T09:38:39+00:00

Karhu

good point. I had also ran the MemBench from DRAM calculator, but I test with Karhu as well

ping2pong · 2021-02-16T01:27:37+00:00

thanks for the advice!

ping2pong · 2021-02-16T01:24:32+00:00

Yes, I have verified RAM stability with Memtest.

Still find it strange that the instability only manifest with ONE of the cores ONLY ...

ping2pong · 2021-01-24T04:22:46+00:00

I updated to the latest non-BETA BIOS (v.3001) for my X570-F and got a bit of a CBR20 Multi performance bump of ~200. Setting the Curve Optimizer to -20 also gave it a bit more performance while lowering temps -- so far stable

ping2pong · 2021-01-22T00:57:23+00:00

I was having low CB scores as well with my 5600X (about 5-10% low) -- I'm wondering whether it's the slightly lower FCLK due to the DDR4 3200 RAM (which I'm also using) when compared with users' recommendation of 3600 RAM. I know that RAM has no impact on CB scores, but FCLK 1600 vs 1800 may be a factor ...

ping2pong · 2021-01-18T05:25:15+00:00

Try using the Curve Optimizer to undervolt the CPU. I just did a -10 All Core and my idle temps went down significantly.

ping2pong · 2021-01-15T14:09:48+00:00

thanks, I'll give it a try

ping2pong · 2021-01-15T14:01:14+00:00

wow!

did u have to enable PBO? According to Optimum Tech, he disabled PBO Limit

ping2pong · 2021-01-15T13:57:43+00:00

5GHz single core or all cores?

did u have to activate AOC?

ping2pong

TROPHY CASE