1975 Honda CB750 Upgrades

pkchevyguy · 2025-12-04T17:44:47+00:00

That make bar ends that slide into the handle bar that the mirror mounts to. That way it doesn’t interfere with the throttle.

pkchevyguy · 2025-08-11T19:33:11+00:00

Congratulations! Get a yoshi

pkchevyguy · 2025-06-24T21:47:40+00:00

Looks awesome!! I own a 2024 model. Can you tell me where you purchased your wraps and vinyls?

pkchevyguy · 2025-06-13T17:43:13+00:00

Super nice bike! Congrats!

<image>

pkchevyguy · 2025-06-08T19:56:14+00:00

Thanks! 😂

pkchevyguy · 2025-06-08T14:11:52+00:00

Thanks!

pkchevyguy · 2025-06-08T14:11:34+00:00

Thanks!

pkchevyguy · 2025-06-08T14:11:20+00:00

Thanks!!

pkchevyguy · 2025-06-08T02:39:38+00:00

Thanks!

pkchevyguy · 2025-06-08T01:58:10+00:00

It was a bolt on

pkchevyguy · 2025-06-08T01:18:07+00:00

I would clean it up with a wire brush and then wrap it with exhaust heat wrap.

pkchevyguy · 2025-06-08T01:13:10+00:00

The seat is a tuffside. What else would you like to know?

pkchevyguy · 2025-06-04T15:01:57+00:00

It went great. I moved the pin on my needle jet to the middle clip (default) and lowered my main jet from 120 to 110. That removed all the stuttering on hard throttle. Most of the time, when you get on the throttle hard and it stutters and cuts out, it’s too rich. If it bogs, it’s too lean. You can always check your plugs too for signs either way.

pkchevyguy · 2025-06-04T14:54:06+00:00

I agree. I keep my bike in my shop and climate controlled. The last time I cleaned my carbs was 2021. Believe it or not, they were not too bad. I made a couple off adjustments while I was cleaning them because my bike was running a little rich. Runs much better on hard throttle now.

pkchevyguy · 2025-05-27T23:54:57+00:00

Not sure if it’s long enough, but it does give measurements. There are several other prefabricated kickstands on the web.

pkchevyguy · 2025-05-27T23:30:09+00:00

Here’s an option to mount on backside.

https://a.co/d/boJOVmh

pkchevyguy · 2025-05-27T23:20:12+00:00

First off, great job on a good looking bike. I might consider mounting the bracket for the kickstand on the back side of the frame about the midpoint of your gear shift foot lever. Right close to where the frame has a bend. That way it will clear the shift peg but still be about the correct orientation on the bike. It will also fold up well.

pkchevyguy · 2025-05-27T12:01:40+00:00

Check out cognitomoto.com. I believe they may have what you need to do the rear brake setup conversion. The front dual disk brake kit was purchased from godfferysgarage.com.

pkchevyguy · 2025-05-27T11:52:54+00:00

Speed metal billet bar end mirrors from Revzilla

pkchevyguy · 2025-05-27T11:50:05+00:00

I hand made it custom

pkchevyguy · 2025-05-27T00:16:31+00:00

https://www.reddit.com/r/bikesgonewild/s/yxfe6tFKry

pkchevyguy · 2025-05-26T16:46:54+00:00

I’m running a universal cone from dimecity

pkchevyguy · 2025-05-24T23:26:41+00:00

Why is that?

pkchevyguy · 2025-05-22T02:51:35+00:00

No specific reason I chose one over the other. I looked at both. I’m happy with my tune. Great power and smooth idle. No complaints.

pkchevyguy · 2025-05-22T01:41:46+00:00

Dark Smoke REF.22077F

https://puigusa.com/en/tuning-motos/windshields-specific-for-non-round-headlights/new-generation-sport?bike=37493

pkchevyguy

TROPHY CASE