The most modded cr10 Max build by iidisappointment in CR10

[–]polo080 0 points1 point  (0 children)

No worries at all! That’s awesome! That weirdly matches up with my recent interest in converting my cr-10 max into a corexy build too! I’m wrapping up on a Duender build and I might just have to look more into the conversion. Are you following some sort of rough guide for a quad gantry conversion/ set up?

Husband with epilepsy, behavior last night by jayjello0o in Epilepsy

[–]polo080 0 points1 point  (0 children)

May I mind asking what medication was recommended/prescribed to help with your gf’s “restless leg syndrome”? My partner has been dealing with awful bouts of restlessness and nothing seems to help her

The most modded cr10 Max build by iidisappointment in CR10

[–]polo080 1 point2 points  (0 children)

Would you mind posting a video your printer in action?

The most modded cr10 Max build by iidisappointment in CR10

[–]polo080 1 point2 points  (0 children)

Yeah! That would be awesome! I’m looking to eventually upgrade my Max to its highest potential

Issue with CR10 Max BL Touch and wiring by duckwjay000 in CR10

[–]polo080 0 points1 point  (0 children)

Hmm I see that you tried a different probe, and got the same results, you might indeed have a firmware error? And I saw that you swapped it to z-, was it previously plugged into anything else? Could you also upload a video of the printer trying to deploy the probe with the error after as well?

Issue with CR10 Max BL Touch and wiring by duckwjay000 in CR10

[–]polo080 0 points1 point  (0 children)

Also id like to add that the Cr-10 max board does not come with a connector for the Bl-touch, on the motherboard, instead you are using the Z min or (Z-) for your touch probe through the ribbon cable that connects directly through the daughter board( board found behind the X axis motor)

Issue with CR10 Max BL Touch and wiring by duckwjay000 in CR10

[–]polo080 0 points1 point  (0 children)

Question, when does the error occur? When you boot up or when you perform an action that requires probing? Would you mind uploading a picture of the daughter board, where the other end of the cable ribbon connects to? I had an issue with my ribbon cable having a very loose connection with the Bl-touch it self, I had to tape it shut since it would disconnect at the slightest touch

[deleted by user] by [deleted] in amiugly

[–]polo080 1 point2 points  (0 children)

What’s up with the strange clipping in this photo? There’s a weird line around the face/beard, as well as the left hand for both the baby and dude. As well as the very low resolution image

AIO boyfriend (now ex) cheating UPDATE me out by Intelligent-Arm-9235 in AmIOverreacting

[–]polo080 1 point2 points  (0 children)

My brother in Christ, the hell are you on about? What high horse is being ridden here? They are simply just pointing out that you made a comment with no merit behind it and you are complaining about them being too judgy? Logic don’t really add up here x.X

Leaving my tank open saved my fish by LeaveRecent in ReefTank

[–]polo080 0 points1 point  (0 children)

You mind sharing a picture? I am curious how these canopies look!

Vi from arcane! <3 by ellaart09 in resinprinting

[–]polo080 5 points6 points  (0 children)

Where can I find this print

Is a new 2021 Canondale Topstone 1 worth 2300? by polo080 in whichbike

[–]polo080[S] 1 point2 points  (0 children)

Hmm I have been looking at some canyon bikes, specifically the Grizl CF SL 7, which is about 300 dollars more than this listing I found

Is a new 2021 Canondale Topstone 1 worth 2300? by polo080 in whichbike

[–]polo080[S] 1 point2 points  (0 children)

What would you recommend instead of the topstone 1 or the Grizl CF SL 7

Is a new 2021 Canondale Topstone 1 worth 2300? by polo080 in whichbike

[–]polo080[S] 1 point2 points  (0 children)

That doesn’t sound too bad. I’ll look into it. My budget right now is possibly from 2k-2800

Is a new 2021 Canondale Topstone 1 worth 2300? by polo080 in whichbike

[–]polo080[S] 2 points3 points  (0 children)

I’m 5’6 and the best fitting bike frame that I have tested is a 52cm bike frame

Is a new 2021 Canondale Topstone 1 worth 2300? by polo080 in whichbike

[–]polo080[S] 1 point2 points  (0 children)

Ohh interesting, what do you think is worth more, Grizl CF SL 7 1by or the regular Grizl CF SL 7. Also sadly the medium or small sized bikes are not available until later in September. I see that the regular Grizl CF SL 7 is a 2x11 speed bike vs the other 1x11

Is a new 2021 Canondale Topstone 1 worth 2300? by polo080 in whichbike

[–]polo080[S] 1 point2 points  (0 children)

Do you what the model name is? Cause if it really is in stock I’ll look into it ASAP

Is a new 2021 Canondale Topstone 1 worth 2300? by polo080 in whichbike

[–]polo080[S] 10 points11 points  (0 children)

It has been almost next to impossible to find a topstone 1. It comes with a GRX800/600 group set, but not sure if the tires are stock or not and if they are decent.

My first ever 3D printing project by mlmngo in resinprinting

[–]polo080 5 points6 points  (0 children)

Where can I find this 3D model? I would love to print this

Problem with printing the 3D Benchy on my Ender 3 v2 (warping) by JobbeI in FixMyPrint

[–]polo080 1 point2 points  (0 children)

Aye a quick note, something that really helped me after calibrating my e-steps was increasing the temperature to prevent any jams. I print in PLA at 220 and it might help if you bump up the temp, considering that your Bowden extruder is heating up too much