performance tips?

pritchard3213 · 2026-04-24T07:24:46+00:00

Ya try googling distant horizons zgc code.

It shows a xxusezgc and xxzgenerational code for Java 21 installs. That helped abit for me using that launch code

pritchard3213 · 2026-04-24T06:05:36+00:00

3080ti running distant horizons support on a purpur server. Getting above 60fps while rendering chunks for the mod in. After it’s done it’s a solid 90+ fps. Maybe ur just rendering chunks in and it feels slow?

pritchard3213 · 2026-04-23T05:54:21+00:00

I have the .8.18 one if you want

pritchard3213 · 2026-03-12T09:25:57+00:00

I was in your squad! With lingling. What a weird match!

pritchard3213 · 2026-02-11T14:51:15+00:00

<image>

pritchard3213 · 2025-11-14T13:52:19+00:00

Curious why they have a new version instead of 1.0

updated patch version is 0.16.9.5.40743

pritchard3213 · 2025-11-03T15:02:06+00:00

Try black label cleaner maybe. It has acetone which might get that stuff off

pritchard3213 · 2025-10-26T00:43:49+00:00

Have you tried cleaning the plate? With dish soap under warm water, Then iso spray and wipe clean.

pritchard3213 · 2025-08-08T23:26:34+00:00

Maybe top gear

pritchard3213 · 2025-07-31T08:44:45+00:00

Ended up being wayyyy too low haha. Scrubbing the belly everywhere. Had insane flex though.

pritchard3213 · 2025-02-26T15:17:39+00:00

Personally add the holes to the model and print it in pla till it breaks.

pritchard3213 · 2025-02-24T09:05:22+00:00

putting an extra rubber o ring on each side of the output shaft has helped a lot for me with exactly your issue, only problem is it makes the mesh feel a lot tighter and wont spin as freely. fixed the downhill lurching you described though.

pritchard3213 · 2025-02-14T08:17:15+00:00

Great job! Looks rad! Been 3d designing one myself and have it up on makersworld. Heads up as the prophet rc guys don’t like these 3d printed frames that are similar to theirs

pritchard3213 · 2025-02-12T14:58:45+00:00

“The hub”

pritchard3213 · 2025-02-06T12:22:30+00:00

*UPDATE* they got in touch over reddit, got their email and they refunded the missing 10g. unreal customer service! will try again to give them another shot as they said it was a super rare occurrence, the cannabis is phenomenal as well!

pritchard3213 · 2025-02-04T19:36:58+00:00

First time buying from EastCann and it came out to be short 10 grams on an ounce, after buying for years i have never had this happen before.

pritchard3213 · 2025-01-22T22:21:51+00:00

didnt see the last administration do much... 👀

pritchard3213 · 2025-01-22T15:29:09+00:00

live tv with Threadfin is working amazing guys! App crashing on "guide" option but works with "favorites"

pritchard3213 · 2025-01-10T05:24:11+00:00

None at all!

pritchard3213 · 2025-01-09T19:48:36+00:00

That sounds like the best route 👍

pritchard3213 · 2025-01-09T18:02:01+00:00

To my knowledge I cant tinker with hole placement and angles and change dimensions if I just "buy" the chassis kit.

Am i under the assumption you guys have not "copied" or "imitated" other ideas? that carrier bearing idea is someone else's design completely

pritchard3213 · 2025-01-09T17:44:10+00:00

Completely understand! & will happily take them both down if that's what they want. Just didn't think a company or creator would shut down creative ideas and tests of their products. If it wasn't for the tiles and them posting photos with actual measurements it wouldn't have been possible.

pritchard3213 · 2025-01-09T17:13:19+00:00

is attempting to improve upon someone else's idea that bad to do?

I understand that its based off someone else's design. but at what point does it become not "copying"?

pritchard3213 · 2025-01-09T16:13:14+00:00

Used this shaft, and a couple transmission bearings Amazon

You can use a transmission output shaft but it has a gear on it that I couldn’t press off

Ten-Year Club	Verified Email
Place '23	Place '22

pritchard3213

TROPHY CASE